- 您现在的位置：买卖IC网 > PDF目录97899 > EL2099C High Speed,Video Distribution Amplifier(高速视频分配放大器) PDF资料下载
参数资料
| 型号： | EL2099C |
| 英文描述： | High Speed,Video Distribution Amplifier(高速视频分配放大器) |
| 中文描述： | 高速，视频分配放大器（高速视频分配放大器） |
| 文件页数： | 2/16页 |
| 文件大小： | 355K |
| 代理商： | EL2099C |
EL2099C
Video Distribution Amplifier
Applications Information
Product Description
The EL2099C is a current mode feedback amplifi-
er that has high output current drive capability
It is built using Elantec’s proprietary dielectric
isolation process that produces NPN and PNP
complimentary transistors The high output cur-
rent can be useful to drive many standard video
loads in parallel as well as digital sync pulses
that are 8V or greater
a
Input Resistor Value
A small value resistor located in the aInput lead
is necessary to keep the EL2099C from oscillat-
ing under certain conditions A 50
X resistor is
recommended
for
all
applications
although
smaller values will work under some circum-
stances All tests listed in this datasheet are per-
formed with 50
X in the aInput lead as well as
all typical performance curves The 50
X resistor
along with the aInput bias current creates an
additional typical Offset Voltage of only 250
mV
at T e 25 C and a maximum of 125 mV over
temperature variations
Feedback Resistor Values
The EL2099C has been designed and specified
with RF e 510X and AV ea2 This value of
feedback resistor yields extremely flat frequency
response with little to no peaking However 3 dB
bandwidth is reduced somewhat because of this
Wider bandwidth at the expense of slight peak-
ing can be accomplished by reducing the value of
the feedback resistor For example at a gain of
a
2 reducing the feedback resistor to 330
X in-
creases the b3 dB bandwidth to 70 MHz with
3 dB of peaking Inversely larger values of feed-
back resistor will cause roll off to occur at a lower
frequency There is essentially no peaking with
RF l 510X
Power Supplies
The EL2099C may be operated with single or
split supplies as low as g5V (10V total) to as
high as g18V (36V total) Bandwidth and slew
rate are almost constant from VS e g10V to
g
18V and decrease slightly as supplies are re-
duced to g5V as shown in the characteristic
curves It is not necessary to use equal value split
supplies For example b5V and b12V would be
fine for 0V to 1V video signals
Good power supply bypassing should be used to
reduce the risk of oscillation A 1
mFto10 mF
tantalum capacitor in parallel with a 01
mF ce-
ramic capacitor is recommended for bypassing
each supply pin They should be kept as close as
possible to the device pins
Due to the internal construction of the TO-220
package the tab of the EL2099C is connected to
the VSb pin Therefore care must be taken to
avoid connecting the tab to the ground plane of
the system
Printed Circuit Board Layout
As with any high frequency device good printed
circuit board layout is necessary for optimum
performance Ground plane construction is high-
ly recommended Lead lengths should be as short
as possible For good AC performance parasitic
capacitances should be kept to a minimum espe-
cially at the inverting input which is sensitive to
stray capacitance
This implies keeping the
ground plane away from this pin Metal film and
carbon resistors are both acceptable while use of
wire-wound resistors is not recommended be-
cause of their parasitic inductance Similarly ca-
pacitors should be low inductance for best per-
formance
Driving Cables and Capacitive Loads
The EL2099C was designed with driving multi-
ple coaxial cables in mind With 440 mA of out-
put drive and low output impedance driving six
75
X double terminated coaxial cables to g11V
with one EL2099C is practical
When used as a cable driver double termination
is always recommended for reflection-free per-
formance For those applications the back termi-
nation series resistor will decouple the EL2099C
from the capacitive cable and allow extensive ca-
pacitive drive For a discussion on some of the
other ways to drive cables see the application
section on driving cables in the EL2003 data
sheet
10
相关PDF资料 |
PDF描述 |
|---|---|
| EL2120C | 100 MHz Current Feedback Amplifier(100 MHz电流反馈放大器) |
| EL2120 | 100 MHz Current Feedback Amplifier |
| EL2120CN | 100 MHz Current Feedback Amplifier |
| EL2120CS | 100 MHz Current Feedback Amplifier |
| EL2126CN | Ultra-low Noise, Low Power, Wideband Amplifier |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL2099CT | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Video Distribution Amplifier |
| EL20X | 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:8 PIN SOP PHOTOTRANSISTOR |
| EL21 | 制造商:Velleman Inc 功能描述: |
| EL210225A | 制造商:Deutsch 功能描述:Relay stock-72 hours |
| EL210-225A | 制造商:Deutsch 功能描述:Relay stock-72 hours |
发布紧急采购，3分钟左右您将得到回复。