参数资料
| 型号： | EL5135IWZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 3/15页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP LONOISE 650MHZ SOT23-5 |
| 标准包装： | 3,000 |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 转换速率： | 475 V/µs |
| 增益带宽积： | 1.5GHz |
| -3db带宽： | 650MHz |
| 电流 - 输入偏压： | 3.7µA |
| 电压 - 输入偏移： | 200µV |
| 电流 - 电源： | 6.7mA |
| 电流 - 输出 / 通道： | 140mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 带卷 (TR) |
11
FN7383.4
May 4, 2007
transfer function contribute to even higher closed loop
bandwidths. For example, the EL5134, EL5135, EL5234 and
EL5235 have a -3dB bandwidth of 650MHz at a gain of 5,
dropping to 150MHz at a gain of 10. It is important to note
that the EL5134, EL5135, EL5234 and EL5235 is designed
so that this “extra” bandwidth in low-gain application does
not come at the expense of stability. As seen in the typical
performance curves, the EL5134, EL5135, EL5234 and
EL5235 in a gain of only 5 exhibited 0.2dB of peaking with a
500
Ω load.
Output Drive Capability
The EL5134, EL5135, EL5234 and EL5235 are designed to
drive a low impedance load. They can easily drive 6VP-P
signal into a 500
Ω load. This high output drive capability
makes the EL5134, EL5135, EL5234 and EL5235 and ideal
choice for RF, IF, and video applications. Furthermore, the
EL5134, EL5135, EL5234 and EL5235 are current-limited at
their outputs, allowing them to withstand momentary short to
ground. However, the power dissipation with output-shorted
cannot exceed the power dissipation capability of the
package.
Driving Cables and Capacitive Loads
Although the EL5134, EL5135, EL5234 and EL5235 are
designed to drive low impedance load, capacitive loads will
decreases the amplifiers’ phase margin. As shown in the
performance curves, capacitive load can result in peaking,
overshoot and possible oscillation. For optimum AC
performance, capacitive loads should be reduced as much
as possible or isolated with a series resistor between 5
Ω to
20
Ω. When driving coaxial cables, double termination is
always recommended for reflection-free performance. When
properly terminated, the capacitance of the coaxial cable will
not add to the capacitive load seen by the amplifier.
Disable/Power-Down
The EL5134 and EL5234 amplifiers can be disabled placing
their outputs in a high impedance state. When disable, each
amplifier current is reduced to 12uA. The EL5134 and
EL5234 are disabled when their CE pins are pulled up to
within 1V of the power suply. Similarly, the amplifiers are
enabled by floating or pulling its CE pin to at least 3V below
the positive supply. For +/-5V supply, this means that
EL5134 and EL5234 amplifiers will be enabled when CE is
2V or less, and disabled when CE is above 4V. Although the
logic levels are not stardard TTL, this choice of logic
voltages allows the EL5134 and EL5234 to be enabled by
typing CE to ground, even in 5V single supply applications.
The CE pin can be driveing from CMOS outputs.
Supply Voltage Range and Single-Supply
Operation
The
EL5134, EL5135, EL5234 and EL5235 have been
designed to operate with supply voltages having a span of
greater than 5V and less than 12V. In practical terms, this
means that they will operate on dual supplies ranging from
±2.5V to ±6V. With single-supply, the
EL5134, EL5135,
EL5234 and EL5235 will operate from 5V to 12V. To prevent
internal circuit latch-up, the slew rate between the negative
and positve supplies must be less than 1V/nS.
As supply voltages continue to decrease, it becomes
necessary to provide input and output voltage ranges that
can get as close as possible to the supply voltages. The
EL5134, EL5135, EL5234 and EL5235 have an input range
which extends to within 2V of either supply. So, for example,
on ±5V supplies, the
EL5134, EL5135, EL5234 and EL5235
have an input range which spans ±3V. The output range of
the
EL5134, EL5135, EL5234 and EL5235 is also quite
large, extending to within 2V of the supply rail. On a ±5V
supply, the output is therefore capable of swinging from
-3.1V to +3.1V. Single-supply output range is larger because
of the increased negative swing due to the external pull-
down resistor to ground.
Power Dissipation
With the wide power supply range and large output drive
capability of the EL5134, EL5135, EL5234 and EL5235, it is
possible to exceed the 150°C maximum junction
temperatures under certain load and power-supply
conditions. It is therefore important to calculate the
maximum junction temperature (TJMAX) for all applications
to determine if power supply voltages, load conditions, or
package type need to be modified for the EL5134, EL5135,
EL5234 and EL5235 to remain in the safe operating area.
These parameters are related as follows:
where:
PDMAXTOTAL is the sum of the maximum power
dissipation of each amplifier in the package (PDMAX)
PDMAX for each amplifier can be calculated as follows:
where:
TMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
PDMAX = Maximum power dissipation of 1 amplifier
VS = Supply voltage
IMAX = Maximum supply current of 1 amplifier
VOUTMAX = Maximum output voltage swing of the
application
RL = Load resistance
Power Supply Bypassing And Printed Circuit
Board Layout
As with any high frequency devices, good printed circuit
board layout is essential for optimum performance. Ground
T
JMAX
T
MAX
θ
JAxPDMAXTOTAL
()
+
=
PD
MAX
2*V
S
I
SMAX
V
S
(
- V
OUTMAX )
V
OUTMAX
R
L
----------------------------
×
+
×
=
EL5134, EL5135, EL5234, EL5235
相关PDF资料 |
PDF描述 |
|---|---|
| AS168X-CB2DG500 | CIRCUIT BRKR THERMAL 50A 2POLE |
| 1-535598-0 | CONN RCPT 20POS .100 DUAL T/H AU |
| AS168X-CB2DG250 | CIRCUIT BRKR THERMAL 25A 2POLE |
| 8-1734516-0 | RCPT 2MM 30P VRT SMT 30AU" |
| 2-1734516-6 | RCPT 2MM 26P VRT SMT 30AU" LOCK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL5135IWZ-T7A | 功能描述:IC OPAMP LONOISE 650MHZ SOT23-5 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| EL513-6 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Logic IC |
| EL513-60 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Logic IC |
| EL513-600 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Logic IC |
| EL513-65 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Logic IC |
发布紧急采购，3分钟左右您将得到回复。