参数资料
| 型号： | EL5150IS |
| 厂商： | Intersil |
| 文件页数： | 4/18页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP LOW OFF 200MHZ 8-SOIC |
| 标准包装： | 97 |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 转换速率： | 100 V/µs |
| 增益带宽积： | 40MHz |
| -3db带宽： | 200MHz |
| 电流 - 输入偏压： | 20nA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 1.35mA |
| 电流 - 输出 / 通道： | 70mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
12
FN7384.7
January 16, 2008
Gain Bandwidth Product
The EL5150 and family members have a gain bandwidth
product of 40MHz for a gain of +5. Bandwidth can be
predicted by the following equation:
(Gain) x (BW) = GainBandwidthProduct
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and same frequency
response as DC levels are changed at the output; this
characteristic is widely referred to as “diffgain-diffphase”.
Many amplifiers have a difficult time with this especially while
driving standard video loads of 150
Ω, as the output current
has a natural tendency to change with DC level. The dG and
dP for these families is a respectable 0.04% and 0.9°, while
driving 150
Ω at a gain of 2. Driving high impedance loads
would give a similar or better dG and dP performance as the
current output demands placed on the amplifier lessen with
increased load.
Driving Capacitive Loads
These devices can easily drive capacitive loads as
demanding as 27pF in parallel with 500
Ω while holding
peaking to within 5dB of peaking at unity gain. Of course if
less peaking is desired, a small series resistor (usually
between 5
Ω to 50Ω) can be placed in series with the output
to eliminate most peaking; however, there will be a small
sacrifice of gain which can be recovered by simply adjusting
the value of the gain resistor.
Driving Cables
Both ends of all cables must always be properly terminated;
double termination is absolutely necessary for reflection-free
performance. Additionally, a back-termination series resistor
at the amplifier's output will isolate the amplifier from the
cable and allow extensive capacitive drive. However, other
applications may have high capacitive loads without a
back-termination resistor. Again, a small series resistor at
the output can help to reduce peaking.
Disable/Power-Down
Devices with disable can be disabled with their output placed
in a high impedance state. The turn off time is about 330ns
and the turn on time is about 130ns. When disabled, the
amplifier's supply current is reduced to 17A typically;
essentially eliminating power consumption. The amplifier's
power down is controlled by standard TTL or CMOS signal
levels at the ENABLE pin. The applied logic signal is relative
to VS- pin. Letting the ENABLE pin float or the application of
a signal that is less than 0.8V above VS- enables the
amplifier. The amplifier is disabled when the signal at
ENABLE pin is above VS+ - 1.5V.
Output Drive Capability
Members of the EL5150 family do not have internal short
circuit protection circuitry. Typically, short circuit currents
ranging from 70mA and 95mA can be expected and
naturally, if the output is shorted indefinitely the part can
easily be damaged from overheating; or excessive current
density may eventually compromise metal integrity.
Maximum reliability is maintained if the output current is
always held below ±40mA. This limit is set and limited by the
design of the internal metal interconnect. Note that in
transient applications, the part is extremely robust.
Power Dissipation
With the high output drive capability of these devices, it is
possible to exceed the +125°C absolute maximum junction
temperature under certain load current conditions.
Therefore, it is important to calculate the maximum junction
temperature for an application to determine if load conditions
or package types need to be modified to assure operation of
the amplifier in a safe operating area.
The maximum power dissipation allowed in a package is
determined according to Equation 1:
Where:
TJMAX = Maximum junction temperature
TAMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage, plus the power in the IC due to the load, or:
For sourcing:
For sinking:
Where:
VS = Supply voltage
ISMAX = Maximum quiescent supply current
VOUT = Maximum output voltage of the application
RLOAD = Load resistance tied to ground
ILOAD = Load current
N = number of amplifiers (Max = 2)
By setting the two PDMAX equations equal to each other, we
can solve the output current and RLOAD to avoid the device
overheat.
PD
MAX
T
JMAX
T
AMAX
–
Θ
JA
---------------------------------------------
=
(EQ. 1)
PD
MAX
V
S
I
SMAX
V
S
V
OUTi
–
()
i1
=
n
∑
V
OUTi
R
Li
-----------------
×
+
×
=
(EQ. 2)
PD
MAX
V
S
I
SMAX
V
OUTi
V
S
–
()
i1
=
n
∑
I
LOADi
×
+
×
=
(EQ. 3)
EL5150, EL5151, EL5250, EL5251, EL5451
相关PDF资料 |
PDF描述 |
|---|---|
| RGH2012-2E-P-393-B | RES 39K OHM .1% 1/4W 0805 SMD |
| 7100.1163.13 | FUSE 630MA 250V FAST 19MM PCB |
| WSLT2512R0200FEA | RES .02 OHM 1W 1% 2512 SMD |
| MMH25-0261Q1 | CONN RACK/PANEL 26POS 5A |
| 929974-01-36-RK | CONN RECEPT .100 SNGL STR 36POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL5150IS-T13 | 功能描述:IC AMP VFA SGL 200MHZ 8-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| EL5150IS-T7 | 功能描述:IC OP AMP LO OFF 200MHZ 8-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| EL5150ISZ | 功能描述:IC AMP VFA SGL 200MHZ 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| EL5150ISZ-T13 | 功能描述:IC AMP VFA SGL 200MHZ 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| EL5150ISZ-T7 | 功能描述:IC AMP VFA SINGLE 200MHZ 8-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。