参数资料
| 型号： | EL5157IWZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 3/17页 |
| 文件大小： | 0K |
| 描述： | IC AMP VFA SGL 600MHZ SOT23-5 |
| 标准包装： | 250 |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 转换速率： | 700 V/µs |
| 增益带宽积： | 210MHz |
| -3db带宽： | 600MHz |
| 电流 - 输入偏压： | 400nA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 6mA |
| 电流 - 输出 / 通道： | 140mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 12 V，±2.25 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 带卷 (TR) |
11
FN7386.6
July 7, 2009
determine if load conditions or package types need to be
modified to assure operation of the amplifier in a safe
operating area.
The maximum power dissipation allowed in a package is
determined according to Equation 2:
Where:
TJMAX = Maximum junction temperature
TAMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage, plus the power in the IC due to the load, or:
For sourcing:
For sinking:
Where:
VS = Supply voltage
ISMAX = Maximum quiescent supply current
VOUT = Maximum output voltage of the application
RLOAD = Load resistance tied to ground
ILOAD = Load current
N = number of amplifiers (max = 2)
By setting the two PDMAX equations equal to each other, we
can solve the output current and RLOAD to avoid the device
overheat.
Power Supply Bypassing Printed Circuit Board
Layout
As with any high frequency device, a good printed circuit
board layout is necessary for optimum performance. Lead
lengths should be as short as possible. The power supply
pin must be well bypassed to reduce the risk of oscillation.
For normal single supply operation, where the VS- pin is
connected to the ground plane, a single 4.7F tantalum
capacitor in parallel with a 0.1F ceramic capacitor from VS+
to GND will suffice. This same capacitor combination should
be placed at each supply pin to ground if split supplies are to
be used. In this case, the VS- pin becomes the negative
supply rail. See Figure 37 for a complete tuned power supply
bypass methodology.
Printed Circuit Board Layout
For good AC performance, parasitic capacitance should be
kept to a minimum. Use of wire wound resistors should be
avoided because of their additional series inductance. Use
of sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance that can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier's inverting input pin is very important. The
feedback resistor should be placed very close to the
inverting input pin. Strip line design techniques are
recommended for the signal traces.
PDMAX
TJMAX TAMAX
–
Θ
JA
---------------------------------------------
=
(EQ. 2)
PDMAX
VS ISMAX
VS VOUTi
–
()
i1
=
n
∑
VOUTi
RLi
-----------------
×
+
×
=
(EQ. 3)
PDMAX
VS ISMAX
VOUTi VS
–
()
i1
=
n
∑
ILOADi
×
+
×
=
(EQ. 4)
EL5156, EL5157, EL5256, EL5257
相关PDF资料 |
PDF描述 |
|---|---|
| RT0603DRD07107KL | RES 107K OHM 1/10W .5% 0603 SMD |
| 0034.1747 | FUSE 1.25A 250V 6.3X32 FAST GLSS |
| EL5156ISZ-T13 | IC AMP VFA SGL 600MHZ 8-SOIC |
| EL5156ISZ | IC AMP VFA SGL 600MHZ 8-SOIC |
| 0034.1746 | FUSE 1A 250V 6.3X32 FAST GLASS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL5158 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Logic IC |
| EL5159 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Logic IC |
| EL5160 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:200MHz Low-Power Current Feedback Amplifiers |
| EL5160_07 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:200MHz Low-Power Current Feedback Amplifiers |
| EL5160IS | 功能描述:IC OP AMP LOW PWR 200MHZ 8-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。