参数资料
| 型号： | EL5167IC-T7 |
| 厂商： | Intersil |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP 1.4GHZ CURR FB SC70-5 |
| 标准包装： | 1 |
| 放大器类型： | 电流反馈 |
| 电路数： | 1 |
| 转换速率： | 6000 V/µs |
| -3db带宽： | 1.4GHz |
| 电流 - 输入偏压： | 8.5µA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 8.5mA |
| 电流 - 输出 / 通道： | 200mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-TSSOP（5 引线），SC-88A，SOT-353 |
| 供应商设备封装： | SC-70-5 |
| 包装： | 剪切带 (CT) |
| 其它名称： | EL5167IC-T7CT |
11
FN7365.6
September 14, 2010
supplies, the EL5166 and EL5167 have an input range
which spans ±3.2V. The output range of the EL5166 and
EL5167 is also quite large, extending to within 1V of the
supply rail. On a ±5V supply, the output is therefore capable
of swinging from -4V to +4V.
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same
frequency response as DC levels are changed at the
output. This is especially difficult when driving a standard
video load of 150
Ω because of the change in output current
with DC level. Previously, good differential gain could only
be achieved by running high idle currents through the
output transistors (to reduce variations in output
impedance.) These currents were typically comparable to
the entire 8.5mA supply current of each EL5166 and
EL5167 amplifier. Special circuitry has been incorporated in
the EL5166 and EL5167 to reduce the variation of output
impedance with the current output. This results in dG and
dP specifications of 0.01% and 0.03°, while driving 150
Ω at
a gain of 2.
Output Drive Capability
In spite of their low 8.5mA of supply current, the EL5166 and
EL5167 are capable of providing a minimum of ±110mA of
output current. With so much output drive, the EL5166 and
EL5167 are capable of driving 50
Ω loads to both rails,
making them an excellent choice for driving isolation
transformers in telecommunications applications.
Driving Cables and Capacitive Loads
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, the back-termination series resistor will
decouple the EL5166 and EL5167 from the cable and allow
extensive capacitive drive. However, other applications may
have high capacitive loads without a back-termination
resistor. In these applications, a small series resistor (usually
between 5
Ω and 50Ω) can be placed in series with the
output to eliminate most peaking. The gain resistor (RG) can
then be chosen to make up for any gain loss which may be
created by this additional resistor at the output. In many
cases it is also possible to simply increase the value of the
feedback resistor (RF) to reduce the peaking.
Current Limiting
The EL5166 and EL5167 have no internal current-limiting
circuitry. If the output is shorted, it is possible to exceed the
Absolute Maximum Rating for output current or power
dissipation, potentially resulting in the destruction of the
device.
Power Dissipation
With the high output drive capability of the EL5166 and
EL5167, it is possible to exceed the +125°C Absolute
Maximum junction temperature under certain very high load
current conditions. Generally speaking, when RL falls below
about 25
Ω, it is important to calculate the maximum junction
temperature (TJMAX) for the application to determine if
power supply voltages, load conditions, or package type
need to be modified for the EL5166 and EL5167 to remain in
the safe operating area. These parameters are calculated as
follows:
where:
TMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
n = Number of amplifiers in the package
PDMAX = Maximum power dissipation of each amplifier in
the package
PDMAX for each amplifier can be calculated as follows:
where:
VS = Supply voltage
ISMAX = Maximum supply current of 1A
VOUTMAX = Maximum output voltage (required)
RL = Load resistance
TJMAX
TMAX θJA nPDMAX
×
()
+
=
(EQ. 1)
PDMAX
2
(
VS ISMAX)
VS
(
VOUTMAX)
VOUTMAX
RL
----------------------------
×
–
+
×
=
(EQ. 2)
EL5166, EL5167
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6079CDHC | IC OP AMP QUAD R-R I/O 16DFN |
| MAX9611AUB+ | IC 12BIT ADC OPAMP COMPAR 10UMAX |
| LT6200IS6#TRPBF | IC OPAMP R-R I/O 165MHZ SOT23-6 |
| MAX44251AUA+ | IC AMP LNA 20V ULT PREC UMAX |
| EL5104IW-T7 | IC OP AMP HS VF 700MHZ SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL5167IC-T7A | 功能描述:运算放大器 - 运放 1.2 GHz CFA Single RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| EL5167ICZ-T7 | 功能描述:高速运算放大器 EL5167ICZ 1 2GHZ CFA RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| EL5167ICZ-T7A | 功能描述:视频放大器 EL5167ICZ 1 2GHZ CFA RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| EL5167IW | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1.4GHz Current Feedback Amplifiers with Enable |
| EL5167IW-T13 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1.4GHz Current Feedback Amplifiers with Enable |
发布紧急采购，3分钟左右您将得到回复。