参数资料
| 型号： | EL5170ISZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 14/14页 |
| 文件大小： | 0K |
| 描述： | IC DRVR TWIST 100MHZ TRPL 8-SOIC |
| 标准包装： | 1 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 转换速率： | 1100 V/µs |
| -3db带宽： | 100MHz |
| 电流 - 输入偏压： | 6µA |
| 电压 - 输入偏移： | 6000µV |
| 电流 - 电源： | 7.4mA |
| 电流 - 输出 / 通道： | 80mA |
| 电压 - 电源，单路/双路(±)： | 4.75 V ~ 11 V，±2.38 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 标准包装 |
| 产品目录页面： | 1238 (CN2011-ZH PDF) |
| 其它名称： | EL5170ISZ-T7DKR |
EL5170, EL5370
9
FN7309.9
August 28, 2012
Description of Operation and
Application Information
Product Description
The EL5170 and EL5370 are wide bandwidth, low power and
single/differential ended to differential output amplifiers. They
have a fixed gain of 2. The EL5170 is a single channel
differential amplifier. The EL5370 is a triple channel
differential amplifier. The EL5170 and EL5370 have a -3dB
bandwidth of 100MHz while driving a 200
Ω differential load.
The EL5170 and EL5370 are available with a power-down
feature to reduce the power while the amplifiers are disabled.
Input, Output and Supply Voltage Range
The EL5170 and EL5370 have been designed to operate with a
single supply voltage of 5V to 10V or split supplies with its total
voltage from 5V to 10V. The amplifiers have an input common
mode voltage range from -4.5V to 3.4V for ±5V supply. The
differential mode input range (DMIR) between the two inputs
is from -2.3V to +2.3V. The input voltage range at the REF pin is
from -3.3V to 3.8V. If the input common mode or differential
mode signal is outside the above-specified ranges, it will cause
the output signal to become distorted.
The output of the EL5170 and EL5370 can swing from -3.3V to
3.6V at 200
Ω differential load at ±5V supply. As the load
resistance becomes lower, the output swing is reduced.
Differential and Common Mode Gain
Settings
As shown in the “Simplified Schematic” on page 8, since the
feedback resistors RF and the gain resistor are integrated with
200
Ω and 400Ω, the EL5170 and EL5370 have a fixed gain of
2. The common mode gain is always one.
Driving Capacitive Loads and Cables
The EL5170 and EL5370 can drive 75pF differential capacitor
in parallel with 200
Ω differential load with less than 3.5dB of
peaking. If less peaking is desired in applications, a small
series resistor (usually between 5
Ω to 50Ω) can be placed in
series with each output to eliminate most peaking. However,
this will reduce the gain slightly.
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, a back-termination series resistor at the
amplifier’s output will isolate the amplifier from the cable and
allow extensive capacitive drive. However, other applications
may have high capacitive loads without a back-termination
resistor. Again, a small series resistor at the output can help to
reduce peaking.
Disable/Power-Down
The EL5170 and EL5370 can be disabled and their outputs
placed in a high impedance state. The turn-off time is about
1s and the turn-on time is about 200ns. When disabled, the
amplifier’s supply current is reduced to 2A for IS+ and 120A
for IS- typically, thereby effectively eliminating the power
consumption. The amplifier’s power-down can be controlled by
standard CMOS signal levels at the ENABLE pin. The applied
logic signal is relative to VS+ pin. Letting the EN pin float or
applying a signal that is less than 1.5V below VS+ will enable
the amplifier. The amplifier will be disabled when the signal at
EN pin is above VS+ -0.5V.
Output Drive Capability
The EL5170 and EL5370 have internal short circuit protection.
Its typical short circuit current is ±80mA. If the output is
shorted indefinitely, the power dissipation could easily
increase such that the part will be destroyed. Maximum
reliability is maintained if the output current never exceeds
±60mA. This limit is set by the design of the internal metal
interconnect.
Power Dissipation
With the high output drive capability of the EL5170 and EL5370
it is possible to exceed the +125°C absolute maximum junction
temperature under certain load current conditions. Therefore, it
is important to calculate the maximum junction temperature for
the application to determine if the load conditions or package
types need to be modified for the amplifier to remain in the safe
operating area.
The maximum power dissipation allowed in a package is
determined according to Equation 1:
Where:
TJMAX = Maximum junction temperature
TAMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
The maximum power dissipation actually produced by an IC is
the total quiescent supply current times the total power supply
voltage, plus the power in the IC due to the load, or as
expressed in Equation 2:
Where:
VSTOT = Total supply voltage = VS+ - VS-
ISMAX = Maximum quiescent supply current per channel
ΔVO = Maximum differential output voltage of the
application
RLD = Differential load resistance
ILOAD = Load current
i = Number of channels
By setting the two PDMAX equations equal to each other, we
can solve the output current and RLOAD to avoid the device
overheat.
PD
MAX
T
JMAX
T
AMAX
–
Θ
JA
---------------------------------------------
=
(EQ. 1)
PD
i
V
STOT
I
SMAX
×
V
(
STOT
ΔV
O )
–
ΔV
O
R
LD
------------
×
+
×
=
(EQ. 2)
相关PDF资料 |
PDF描述 |
|---|---|
| GEC26SGSN-M89 | CONN HEADER 26POS .100 RT/A SMD |
| 10-89-7462 | CONN HDR DUAL 46POS .100 SRT AU |
| PBC35SACN | CONN HEADER .100 SINGL STR 35POS |
| 929450-01-12-I | CONN HEADER .100 SNGL STR 12POS |
| 929836-05-09 | CONN HEADER .100 DUAL STR 18POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL5170IY | 功能描述:IC DRIVER DIFF 100MHZ TP 8-MSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| EL5170IY-T13 | 功能描述:IC DRVR SGL 100MHZ DIFF 8-MSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| EL5170IY-T7 | 功能描述:IC DRIVER DIFF 100MHZ TP 8-MSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| EL5170IYZ | 功能描述:差分放大器 EL5170IYZ 100MHZ DIF DRVR GAIN=2 RoHS:否 制造商:Texas Instruments 通道数量:1 Channel 带宽:2.4 GHz 可用增益调整:6 dB to 26 dB 输入补偿电压: 共模抑制比（最小值）:- 40 dB 工作电源电压:4.75 V to 5.25 V 电源电流:100 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:WQFN-24 封装:Reel |
| EL5170IYZ-T13 | 功能描述:差分放大器 EL5170IYZ 100MHZ DIF DRVR GAIN=2 RoHS:否 制造商:Texas Instruments 通道数量:1 Channel 带宽:2.4 GHz 可用增益调整:6 dB to 26 dB 输入补偿电压: 共模抑制比（最小值）:- 40 dB 工作电源电压:4.75 V to 5.25 V 电源电流:100 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:WQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。