参数资料
| 型号： | EL5171IS-T13 |
| 厂商： | Intersil |
| 文件页数： | 3/15页 |
| 文件大小： | 0K |
| 描述： | IC DRVR SGL 250MHZ DIFF 8-SOIC |
| 标准包装： | 2,500 |
| 放大器类型： | 差分 |
| 电路数： | 1 |
| 输出类型： | 差分 |
| 转换速率： | 800 V/µs |
| 增益带宽积： | 100MHz |
| -3db带宽： | 250MHz |
| 电流 - 输入偏压： | 6µA |
| 电压 - 输入偏移： | 1500µV |
| 电流 - 电源： | 7.5mA |
| 电流 - 输出 / 通道： | 120mA |
| 电压 - 电源，单路/双路(±)： | 4.75 V ~ 11 V，±2.38 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
EL5171, EL5371
11
FN7307.8
August 28, 2012
Where:
RF1 = RF2 = RF
FIGURE 26.
Choice of Feedback Resistor and Gain
Bandwidth Product
For applications that require a gain of +1, no feedback resistor
is required. Just short the OUT+ pin to the FBP pin and the OUT-
pin to the FBN pin. For gains greater than +1, the feedback
resistor forms a pole with the parasitic capacitance at the
inverting input. As this pole becomes smaller, the amplifier's
phase margin is reduced. This causes ringing in the time
domain and peaking in the frequency domain. Therefore, RF has
some maximum value that should not be exceeded for optimum
performance. If a large value of RF must be used, a small
capacitor in the few Pico farad range in parallel with RF can help
to reduce the ringing and peaking at the expense of reducing
the bandwidth.
The bandwidth of the EL5171 and EL5371 depends on the load
and the feedback network. RF and RG appear in parallel with
the load for gains other than +1. As this combination gets
smaller, the bandwidth falls off. Consequently, RF also has a
minimum value that should not be exceeded for optimum
bandwidth performance. For gain of +1, RF = 0 is optimum. For
the gains other than +1, optimum response is obtained with RF
between 500
Ω to 1kΩ.
The EL5171 and EL5371 have a gain bandwidth product of
100MHz for RLD = 1kΩ. For gains ≥5, their bandwidth can be
predicted by Equation 3:
Driving Capacitive Loads and Cables
The EL5171 and EL5371 can drive 50pF differential capacitor
in parallel with 1k
Ω differential load with less than 5dB of
peaking at gain of +1. If less peaking is desired in applications,
a small series resistor (usually between 5
Ω to 50Ω) can be
placed in series with each output to eliminate most peaking.
However, this will reduce the gain slightly. If the gain setting is
greater than 1, the gain resistor RG can then be chosen to
make up for any gain loss, which may be created by the
additional series resistor at the output.
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, a back-termination series resistor at the
amplifier's output will isolate the amplifier from the cable and
allow extensive capacitive drive. However, other applications
may have high capacitive loads without a back-termination
resistor. Again, a small series resistor at the output can help to
reduce peaking.
Disable/Power-Down (for EL5371 only)
The EL5371 can be disabled and its outputs placed in a high
impedance state. The turn-off time is about 0.95s and the
turn-on time is about 215ns. When disabled, the amplifier's
supply current is reduced to 1.7A for IS+ and 120A for IS-
typically, thereby effectively eliminating the power
consumption. The amplifier's power-down can be controlled by
standard CMOS signal levels at the ENABLE pin. The applied
logic signal is relative to the VS+ pin. Letting the EN pin float or
applying a signal that is less than 1.5V below VS+ will enable
the amplifier. The amplifier will be disabled when the signal at
the EN pin is above VS+ - 0.5V.
Output Drive Capability
The EL5171 and EL5371 have internal short circuit protection.
Its typical short circuit current is ±90mA for EL5171 and ±70mA
for EL5371. If the output is shorted indefinitely, the power
dissipation could easily increase such that the part will be
destroyed. Maximum reliability is maintained if the output
current never exceeds ±60mA. This limit is set by the design of
the internal metal interconnections.
Power Dissipation
With the high output drive capability of the EL5171 and EL5371,
it is possible to exceed the +135°C absolute maximum junction
temperature under certain load current conditions. Therefore, it
is important to calculate the maximum junction temperature for
the application to determine if the load conditions or package
types need to be modified for the amplifier to remain in the safe
operating area.
The maximum power dissipation allowed in a package is
determined according to Equation 4:
Where:
TJMAX = Maximum junction temperature
TAMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
The maximum power dissipation actually produced by an IC is
the total quiescent supply current times the total power supply
V
ODM
V
IN
(
+V
IN- )
1
2R
F
R
G
-----------
+
×
–
=
(EQ. 2
VO+
FBP
RG
RF2
IN+
IN-
REF
FBN
VIN+
VIN-
VREF
RF1
VO-
Gain
BW
100MHz
=
×
(EQ. 3)
PD
MAX
T
JMAX
T
AMAX
–
Θ
JA
---------------------------------------------
=
(EQ. 4)
相关PDF资料 |
PDF描述 |
|---|---|
| EL5170IY-T13 | IC DRVR SGL 100MHZ DIFF 8-MSOP |
| EL5170IS-T13 | IC DRVR SGL 100MHZ DIFF 8-SOIC |
| PPTC201LGBN-RC | CONN FEMALE 20POS .100" R/A TIN |
| PPPC351LGBN-RC | CONN FEMALE 35POS .100" R/A GOLD |
| EL5166IS-T13 | IC AMP CFA SGL 1.4GHZ 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL5171IS-T7 | 功能描述:IC DRIVER DIFF 250MHZ TP 8-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| EL5171ISZ | 功能描述:差分放大器 EL5171ISZ 200MHZ DIF DRVR EXTERNAL FEEDB RoHS:否 制造商:Texas Instruments 通道数量:1 Channel 带宽:2.4 GHz 可用增益调整:6 dB to 26 dB 输入补偿电压: 共模抑制比（最小值）:- 40 dB 工作电源电压:4.75 V to 5.25 V 电源电流:100 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:WQFN-24 封装:Reel |
| EL5171ISZ | 制造商:Intersil Corporation 功能描述:Differential Line Driver IC |
| EL5171ISZ-T13 | 功能描述:差分放大器 EL5171ISZ 200MHZ DIF DRVR EXTERNAL FEEDB RoHS:否 制造商:Texas Instruments 通道数量:1 Channel 带宽:2.4 GHz 可用增益调整:6 dB to 26 dB 输入补偿电压: 共模抑制比（最小值）:- 40 dB 工作电源电压:4.75 V to 5.25 V 电源电流:100 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:WQFN-24 封装:Reel |
| EL5171ISZ-T7 | 功能描述:差分放大器 EL5171ISZ 200MHZ DIF DRVR EXTERNAL FEEDB RoHS:否 制造商:Texas Instruments 通道数量:1 Channel 带宽:2.4 GHz 可用增益调整:6 dB to 26 dB 输入补偿电压: 共模抑制比（最小值）:- 40 dB 工作电源电压:4.75 V to 5.25 V 电源电流:100 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:WQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。