参数资料
型号: EL5221CYZ-T7
厂商: Intersil
文件页数: 3/13页
文件大小: 0K
描述: IC OPAMP DUAL R-R 12MHZ 8-MSOP
标准包装: 1,500
放大器类型: 缓冲器
电路数: 2
输出类型: 满摆幅
转换速率: 10 V/µs
-3db带宽: 12MHz
电流 - 输入偏压: 2nA
电压 - 输入偏移: 2000µV
电流 - 电源: 500µA
电流 - 输出 / 通道: 120mA
电压 - 电源,单路/双路(±): 4.5 V ~ 16.5 V,±2.25 V ~ 8.25 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)
供应商设备封装: 8-MSOP
包装: 带卷 (TR)
11
FN7187.2
July 25, 2007
Unused Buffers
It is recommended that any unused buffer have the input tied
to the ground plane.
Driving Capacitive Loads
The EL5221 can drive a wide range of capacitive loads. As
load capacitance increases, however, the -3dB bandwidth of
the device will decrease and the peaking increase. The
buffers drive 10pF loads in parallel with 10k
Ω with just 1.5dB
of peaking, and 100pF with 6.4dB of peaking. If less peaking
is desired in these applications, a small series resistor
(usually between 5
Ω and 50Ω) can be placed in series with
the output. However, this will obviously reduce the gain
slightly. Another method of reducing peaking is to add a
"snubber" circuit at the output. A snubber is a shunt load
consisting of a resistor in series with a capacitor. Values of
150
Ω and 10nF are typical. The advantage of a snubber is
that it does not draw any DC load current or reduce the gain
Power Supply Bypassing and Printed Circuit
Board Layout
The EL5221 can provide gain at high frequency. As with any
high frequency device, good printed circuit board layout is
necessary for optimum performance. Ground plane
construction is highly recommended, lead lengths should be
as short as possible, and the power supply pins must be well
bypassed to reduce the risk of oscillation. For normal single
supply operation, where the VS- pin is connected to ground,
a 0.1F ceramic capacitor should be placed from VS+ to pin
to VS- pin. A 4.7F tantalum capacitor should then be
connected in parallel, placed in the region of the buffer. One
4.7F capacitor may be used for multiple devices. This same
capacitor combination should be placed at each supply pin
to ground if split supplies are to be used.
EL5221
相关PDF资料
PDF描述
EL5236IYZ-T13 IC OPAMP GP 300MHZ DUAL LN 8MSOP
EL5292CS-T7 IC AMP CFA DUAL 600MHZ 8-SOIC
EL5293CSZ-T7 IC AMP CFA DUAL 300MHZ 8-SOIC
EL5308IUZ IC AMP FGA TRPL 450MHZ 16-QSOP
EL5360IUZ-T13 IC AMP CFA TRIPLE 200MHZ 16-QSOP
相关代理商/技术参数
参数描述
EL5223 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12MHz 4, 8, 10 & 12 Channel Rail-to-Rail Input-Output Buffers
EL5223CL 功能描述:IC OPAMP 10-CH R-R 12MHZ 24-QFN RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源,单路/双路(±):1.8 V ~ 5.25 V,±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽) 供应商设备封装:10-MSOP 包装:管件
EL5223CL-T13 功能描述:IC OPAMP 10-CH R-R 12MHZ 24-QFN RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源,单路/双路(±):1.8 V ~ 5.25 V,±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽) 供应商设备封装:10-MSOP 包装:管件
EL5223CL-T7 功能描述:IC OPAMP 10-CH R-R 12MHZ 24-QFN RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源,单路/双路(±):1.8 V ~ 5.25 V,±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽) 供应商设备封装:10-MSOP 包装:管件
EL5223CLZ 功能描述:运算放大器 - 运放 EL5223CLZ OCTAL 12MH Z R2R I/O BUFR RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比(最小值):63 dB 输入补偿电压:1 mV 输入偏流(最大值):10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel