参数资料
| 型号： | EL5364IUZ-T13 |
| 厂商： | Intersil |
| 文件页数： | 2/17页 |
| 文件大小： | 0K |
| 描述： | IC AMP CFA TRIPLE 600MHZ 16-QSOP |
| 标准包装： | 2,500 |
| 放大器类型： | 电流反馈 |
| 电路数： | 3 |
| 转换速率： | 4200 V/µs |
| -3db带宽： | 600MHz |
| 电流 - 输入偏压： | 2µA |
| 电压 - 输入偏移： | 1500µV |
| 电流 - 电源： | 3.5mA |
| 电流 - 输出 / 通道： | 140mA |
| 电压 - 电源，单路/双路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
EL5164, EL5165, EL5364
10
FN7389.9
January 30, 2014
Disable/Power-Down
The EL5164 and EL5364 amplifiers can be disabled, placing
their outputs in a high impedance state. When disabled, the
amplifiers supply current reduces to <25A per amplifier. An
amplifier disables when its CE pin is pulled up to within 1V of the
positive supply. Similarly, the amplifier is enabled by floating or
pulling its CE pin to at least 3V below the positive supply. For a
±5V supply, this means that an amplifier enables when its CE is
2V or less, and disables when CE is above 4V. Although the logic
levels are not standard TTL, this choice of logic voltages allows
the amplifiers to be enabled by tying CE to ground, even in 5V
single supply applications. The CE pin can be driven from CMOS
outputs.
When the amplifier is disabled, if the positive input is driven
beyond ±2V with respect to the negative input, the device can
become active and output the signal. An input diode clamp
the device disabled while a large input signal is present.
Capacitance at the Inverting Input
Any manufacturer’s high-speed voltage- or current-feedback
amplifier can be affected by stray capacitance at the inverting
input. For inverting gains, this parasitic capacitance has little
effect because the inverting input is a virtual ground, but for non-
inverting gains, this capacitance (in conjunction with the
feedback and gain resistors) creates a pole in the feedback path
of the amplifier. This pole, if low enough in frequency, has the
same destabilizing effect as a zero in the forward open-loop
response. The use of large-value feedback and gain resistors
exacerbates the problem by further lowering the pole frequency
(increasing the possibility of oscillation.)
The EL5164, EL5165, and EL5364 are optimized for a 510
Ω
feedback resistor at AV = +1. With the high bandwidth of these
amplifiers, these resistor values might cause stability problems
when combined with parasitic capacitance, thus ground plane is
not recommended around the inverting input pin of the amplifier.
Feedback Resistor Values
The EL5164, EL5165, and EL5364 have been designed and
specified for a gain of +2 with RF approximately 412Ω. This value
of feedback resistor gives 450MHz of -3dB bandwidth at AV = 2
with 1dB of peaking. With AV = -2, an RF of 300Ω gives 275MHz
of bandwidth with 1dB of peaking. Since the EL5164, EL5165,
and EL5364 are current-feedback amplifiers, it is also possible to
change the value of RF to get more bandwidth. As seen in the
curves of “Frequency Response for Various RF”, bandwidth and
peaking can be easily modified by varying the value of the
feedback resistor.
Because the EL5164, EL5165, and EL5364 are current-feedback
amplifiers, their gain-bandwidth product is not a constant for
different closed-loop gains. This feature actually allows the
EL5164, EL5165, and EL5364 to maintain about the same -3dB
bandwidth. As gain is increased, bandwidth decreases slightly
while stability increases. Since the loop stability is improving with
higher closed-loop gains, it becomes possible to reduce the value
of RF below the specified 412Ω and still retain stability, resulting
in only a slight loss of bandwidth with increased closed-loop gain.
Supply Voltage Range and Single-Supply
Operation
The EL5164, EL5165, and EL5364 are designed to operate with
supply voltages having a span of 5V to 10V. In practical terms,
this means that they will operate on dual supplies ranging from
±2.5V to ±5V. With a single-supply, the EL5164, EL5165, and
EL5364 will operate from 5V to 10V.
As supply voltages continue to decrease, it becomes necessary to
provide input and output voltage ranges that can get as close as
possible to the supply voltages. The EL5164, EL5165, and
EL5364 have an input range which extends to within 2V of either
supply. For example, on ±5V supplies, the EL5164, EL5165, and
EL5364 have an input range which spans ±3V. The output range
of the EL5164, EL5165, and EL5364 is also quite large,
extending to within 1V of the supply rail. On a ±5V supply, the
output is therefore capable of swinging from -4V to +4V. Single-
supply output range is larger because of the increased negative
swing due to the external pull-down resistor to ground.
Video Performance
For good video performance, an amplifier must maintain the same
output impedance and the same frequency response as DC levels
are changed at the output. This is especially difficult when driving
a standard video load of 150
Ω, because of the change in output
current with DC level. Previously, good differential gain could only
be achieved by running high idle currents through the output
transistors (to reduce variations in output impedance.) These
currents were typically comparable to the entire 3.5mA supply
current of each EL5164, EL5165, and EL5364 amplifier. Special
circuitry has been incorporated in the EL5164, EL5165, and
EL5364 to reduce the variation of output impedance with current
output. This results in dG and dP specifications of 0.01% and
0.01°, while driving 150
Ω at a gain of 2.
Video performance has also been measured with a 500
Ω load at a
gain of +1. Under these conditions, the EL5164, EL5165, and
EL5364 have dG and dP specifications of 0.01% and 0.01°,
respectively.
+
-
D1
D2
+5V
-5V
VOUT
RG
RF
VIN
CE
+5V
FIGURE 23. DISABLED AMPLIFIER
相关PDF资料 |
PDF描述 |
|---|---|
| 151667-4 | CONN RCPT/TAB STR TIN .375 |
| 3372-5502 | CONN HEADER 60PS R/A SHORT LA |
| P50LE-050P1-RR1-DA | CONN PLUG 50POS R/A .050" GOL |
| F20B11505ACFA06E | THERMOSTAT 115 DEG C NO W/LEADS |
| F20B11005ACFA06E | THERMOSTAT 110 DEG C NO W/LEADS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL5364IUZ-T7 | 功能描述:高速运算放大器 EL5364IUZ TRPL 850 MHZ CFAW ENABLE RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| EL5364IUZ-T7R5289 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| EL5367 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1GHz Triple Current Feedback Amplifier |
| EL5367IU | 功能描述:IC AMPLIFIER TRPL 1GHZ 16-QSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| EL5367IU-T13 | 功能描述:IC AMP CFA TRIPLE 1GHZ 16-QSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
发布紧急采购，3分钟左右您将得到回复。