参数资料
| 型号： | EL5373IUZ-T13 |
| 厂商： | Intersil |
| 文件页数： | 3/14页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER TRIPLE 450MHZ 24-QSOP |
| 标准包装： | 2,500 |
| 放大器类型： | 差分 |
| 电路数： | 3 |
| 输出类型： | 差分 |
| 转换速率： | 1100 V/µs |
| -3db带宽： | 450MHz |
| 电流 - 输入偏压： | 13µA |
| 电压 - 输入偏移： | 3000µV |
| 电流 - 电源： | 12mA |
| 电流 - 输出 / 通道： | 50mA |
| 电压 - 电源，单路/双路(±)： | 4.75 V ~ 11 V，±2.38 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 带卷 (TR) |
EL5173, EL5373
11
FN7312.9
August 28, 2012
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, a good printed circuit board
layout is necessary for optimum performance. Lead lengths
should be as short as possible. The power supply pin must be
well bypassed to reduce the risk of oscillation. For normal
single supply operation, where the VS- pin is connected to the
ground plane, a single 4.7F tantalum capacitor in parallel
with a 0.1F ceramic capacitor from VS+ to GND will suffice.
This same capacitor combination should be placed at each
supply pin to ground if split supplies are to be used. In this
case, the VS- pin becomes the negative supply rail.
For good AC performance, parasitic capacitance should be
kept to minimum. Use of wire-wound resistors should be
avoided because of their additional series inductance. Use of
sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance that can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier’s inverting input pin is very important. The
feedback resistor should be placed very close to the inverting
input pin. Strip line design techniques are recommended for
the signal traces.
Typical Applications
0
Ω
VFB
VINB
VREF
EL5175/
EL5375
EL5173/
EL5373
VOUT
50
ZO = 100Ω
VIN
50
Ω
50
Ω
FIGURE 25. TWISTED PAIR CABLE DRIVER
相关PDF资料 |
PDF描述 |
|---|---|
| F20B075051ZA0060 | THERMOSTAT 75 DEG C NO W/PC PIN |
| SMBJ6.0CA/1 | TVS 600W 6V BI-DIR SMB |
| F20B070051ZA0060 | THERMOSTAT 70 DEG C NO W/PC PIN |
| SMBJ36CA/1 | TVS 600W 36V BI-DIR SMB |
| F20B14005ACFA06E | THERMOSTAT 140 DEG C NO W/LEADS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL5373IUZ-T7 | 功能描述:差分放大器 EL5373IUZ TPL 500MHZ DIFF DRVR GAIN=2 RoHS:否 制造商:Texas Instruments 通道数量:1 Channel 带宽:2.4 GHz 可用增益调整:6 dB to 26 dB 输入补偿电压: 共模抑制比（最小值）:- 40 dB 工作电源电压:4.75 V to 5.25 V 电源电流:100 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:WQFN-24 封装:Reel |
| EL5374 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:500MHz Differential Twisted-Pair Drivers |
| EL5374IU | 功能描述:差分放大器 Line Rec DIFF 550MHZ RoHS:否 制造商:Texas Instruments 通道数量:1 Channel 带宽:2.4 GHz 可用增益调整:6 dB to 26 dB 输入补偿电压: 共模抑制比（最小值）:- 40 dB 工作电源电压:4.75 V to 5.25 V 电源电流:100 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:WQFN-24 封装:Reel |
| EL5374IU-T13 | 功能描述:IC DRIVER TRIPLE 550MHZ 28-QSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
| EL5374IU-T7 | 功能描述:IC AMP TRPL DIFF 550MHZ 28-QSOP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。