- 您现在的位置：买卖IC网 > PDF目录20537 > EL7158ISZ-T7A (Intersil)IC PIN DVR 40MHZ 3ST 8SOIC PDF资料下载
参数资料
| 型号： | EL7158ISZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 8/9页 |
| 文件大小： | 0K |
| 描述： | IC PIN DVR 40MHZ 3ST 8SOIC |
| 标准包装： | 250 |
| 配置： | 高端或低端 |
| 输入类型： | 非反相 |
| 延迟时间： | 22ns |
| 电流 - 峰： | 12A |
| 配置数： | 1 |
| 输出数： | 1 |
| 电源电压： | 4.5 V ~ 12 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
EL7158
PD = ( V S × I S ) + ( C INT × V S × f ) + ( C L × V OUT × f )
Applications Information
Product Description
The EL7158 is a high performance 40MHz pin driver. It
contains two analog switches connecting VH and VL to OUT.
Depending on the value of the IN pin, one of the two
switches will be closed and the other switch open. An output
enable (OE) is also supplied which opens both switches
simultaneously.
Due to the topology of the EL7158, both the VH and VL pins
can be connected to any voltage between the VS+ and VS-
pins, but VH must be greater than VL in order to prevent
turning on the body diode at the output stage.
Three-State Operation
When the OE pin is low, the output is three-state (floating).
The output voltage is the parasitic capacitance’s voltage. It
can be any voltage between VH and VL, depending on the
previous state. At three-state, the output voltage can be
pushed to any voltage between VH and V L . The output
voltage can’t be pushed higher than VH or lower than VL
since the body diode at the output stage will turn on.
Supply Voltage Range and Input Compatibility
The EL7158 is designed for operation on supplies from 5V to
18V (4.5V to 18V maximum). Table 2 shows the
specifications for the relationship between the VS+, VS-, VH,
Power Dissipation Calculation
When switching at high speeds, or driving heavy loads, the
EL7158 drive capability is limited by the rise in die
temperature brought about by internal power dissipation. For
reliable operation die temperature must be kept below
T JMAX (+125°C). It is necessary to calculate the power
dissipation for a given application prior to selecting the
package type.
Power dissipation may be calculated:
2 2
(EQ. 1)
where:
V S is the total power supply to the EL7158 (from V S + to
GND)
V OUT is the swing on the output (V H - V L )
C L is the load capacitance
C INT is the internal load capacitance (100pF max)
I S is the quiescent supply current (3mA max)
f is frequency
Having obtained the application’s power dissipation, a
maximum package thermal coefficient may be determined,
to maintain the internal die temperature below T JMAX :
θ JA = -----------------------------------------
VL, and GND pins.
All input pins are compatible with both 3V and 5V CMOS
T JMAX – T MAX
PD
(EQ. 2)
signals. With a positive supply (V S +) of 5V, the EL7158 is
also compatible with TTL inputs.
Power Supply Bypassing
When using the EL7158, it is very important to use adequate
power supply bypassing. The high switching currents
developed by the EL7158 necessitate the use of a bypass
capacitor between the supplies (V S + and V S -) and GND
pins. It is recommended that a 2.2μF tantalum capacitor be
used in parallel with a 0.1μF low-inductance ceramic MLC
capacitor. These should be placed as close to the supply
pins as possible. It is also recommended that the V H and V L
pins have some level of bypassing, especially if the EL7158
is driving highly capacitive loads.
where:
T JMAX is the maximum junction temperature (+125°C)
T MAX is the maximum operating temperature
PD is the power dissipation calculated above
θ JA thermal resistance on junction to ambient
θ JA is 160°C/W for the SOIC8 package when using a
standard JEDEC JESD51-3 single-layer test board. If T JMAX
is greater than +125°C when calculated using Equation 2 ,
then one of the following actions must be taken:
Reduce θ JA the system by designing more heat-sinking
into the PCB (as compared to the standard JEDEC
JESD51-3)
De-rate the application either by reducing the switching
frequency, the capacitive load, or the maximum operating
(ambient) temperature (T MAX )
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
8
FN7349.2
May 14, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| REC3-483.3DRWZ/H/B | CONV DC/DC 3W 18-72VIN +/-3.3V |
| RACD60-1050/IP67 | LED DRIVER 1.05AOUT 33.5-48VOUT |
| REC3-4815SRWZ/H4/C | CONV DC/DC 3W 18-72VIN 15VOUT |
| REC3-4815SRWZ/H4/A | CONV DC/DC 3W 18-72VIN 15VOUT |
| HIP4086ABT | IC DRIVER MOSFET N-CH 3PH 24SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL7182 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:2-Phase, High Speed CCD Driver |
| EL7182_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:2-Phase, High Speed CCD Driver |
| EL7182C | 制造商:ELANTEC 制造商全称:ELANTEC 功能描述:2-Phase, High Speed CCD Driver |
| EL7182CN | 功能描述:功率驱动器IC EL7182CN 10MHZ CCD DRVR RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| EL7182CS | 功能描述:IC CCD DRIVER 2-PHS HS 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。