- 您现在的位置：买卖IC网 > PDF目录20679 > EL7513IY-T7 (Intersil)IC LED DRIVR WHITE BCKLGT 8-MSOP PDF资料下载
参数资料
| 型号： | EL7513IY-T7 |
| 厂商： | Intersil |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT 8-MSOP |
| 标准包装： | 1,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 800kHz ~ 1.2MHz |
| 电源电压： | 2.6 V ~ 13.2 V |
| 输出电压： | 18V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
EL7513
When choosing an inductor, make sure the inductor can
handle the average and peak currents giving by following
formulas (80% efficiency assumed):
The diode should be Schottky type with minimum reverse
voltage of 20V. The diode's peak current is the same as
inductor's peak current, the average current is I O , and RMS
0.8 × V IN
I O × V O
I LAVG = ------------------------
(EQ. 2)
current is:
I DRMS =
I LAVG × I O
(EQ. 5)
I LPK = I LAVG + --- × Δ I L
V IN × ( V O – V IN )
Δ I L = ---------------------------------------------
1
2
L × V O × F S
(EQ. 3)
(EQ. 4)
Ensure the diode's ratings exceed these current
requirements.
White LED Connections
One leg of LEDs connected in series will ensure the
uniformity of the brightness. 18V maximum voltage enables
where:
? Δ I L is the peak-to-peak inductor current ripple in Ampere
? L inductance in μH
? FS switching frequency, typical 1MHz
A wide range of inductance (6.8μH - 68μH) can be used for
the converter to function correctly. For the same series of
inductors, the lower inductance has lower DC resistance
(DCR), which has less conducting loss. But the ripple current
is bigger, which generates more RMS current loss. Figure 11
shows the efficiency of the demo board under different
inductance for a specific series of inductor. For optimal
efficiency in an application, it is a good exercise to check
several adjacent inductance values of your preferred series
of inductors.
For the same inductance, higher overall efficiency can be
obtained by using lower DCR inductor.
EFFICIENCY vs I O
4 LEDs can be placed in series.
However, placing LEDs into series/parallel connection can
give higher efficiency as shown in the efficiency curves. One
of the ways to ensure the brightness uniformity is to pre-
screen the LEDs.
PCB Layout Considerations
The layout is very important for the converter to function
properly. Power Ground ( ) and Signal Ground ( ) should
be separated to ensure the high pulse current in the power
ground does not interference with the sensitive signals
connected to Signal Ground. Both grounds should only be
connected at one point right at the chip. The heavy current
paths (V IN -L-L X pin-PGND, and V IN -L-D-C 2 -PGND) should
be as short as possible.
The trace connected to the CS pin is most important. The
current sense resister R 1 should be very close to the pin
When the trace is long, use a small filter capacitor close to
the CS pin.
85
83
V IN = 3.3V FOR
DIFFERENT L
L = 22μH
The heat of the IC is mainly dissipated through the PGND
pin. Maximizing the copper area around the plane is
preferable. In addition, a solid ground plane is always helpful
L = 33μH
L = 15μH
for the EMI performance.
81
79
77
L = 10μH
L = Coilcraft
LPO1704 SERIES
1mm HEIGHT
The demo board is a good example of layout based on the
principle. Please refer to the EL7513 Application Brief for the
layout.
5
10
15
20
25
30
I O (mA)
FIGURE 21. EFFICIENCY OF DIFFERENT INDUCTANCE
(4 LEDs IN A SERIES)
10
FN7112.5
December 22, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| UMK105B7472KV-F | CAP CER 4700PF 50V 10% X7R 0402 |
| VE-JNF-CX-F3 | CONVERTER MOD DC/DC 72V 75W |
| ECA10DRSN-S288 | CONN EDGECARD 20POS .125 EXTEND |
| ZL2004ALNFT-01 | IC REG CTRLR BUCK SYNC ADJ 32QFN |
| RMM36DRMT-S273 | CONN EDGECARD 72POS .156 SQ WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL7513IYZ | 功能描述:IC LED DRIVR WHITE BCKLGT 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT |
| EL7513IYZ | 制造商:Intersil Corporation 功能描述:Supply Voltage Max.:13.2V |
| EL7513IYZ-T13 | 功能描述:IC LED DRIVR WHITE BCKLGT 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT |
| EL7513IYZ-T7 | 功能描述:IC LED DRIVR WHITE BCKLGT 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT |
| EL7515 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Frequency PWM Step-Up Regulator |
发布紧急采购，3分钟左右您将得到回复。