参数资料
| 型号： | EL7584IRZ-T13 |
| 厂商： | Intersil |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC CONV DC/DC 4-CHAN 24-TSSOP |
| 标准包装： | 2,500 |
| 应用： | 转换器，TFT，LCD |
| 输入电压： | 2 V ~ 14 V |
| 输出数： | 2 |
| 输出电压： | 5 V ~ 17 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
EL7584
I OMAX = ? I LMT – ------- ? × ---------
V O
Δ I L = --------- × -------
F S
V O - V IN
Applications Information
The EL7584 is high efficiency multiple output power solution
designed specifically for thin-film transistor (TFT) liquid
crystal display (LCD) applications. The device contains one
high current boost converter and two low power charge
pumps (V ON and V OFF ).
The boost converter contains an integrated N-channel
MOSFET to minimize the number of external components.
The converter output voltage can be set from 5V to 18V with
external resistors. The V ON and V OFF charge pumps are
independently regulated to positive and negative voltages
using external resistors. Output voltages as high as 40V can
be achieved with additional capacitors and diodes.
Boost Converter
The boost converter operates in constant frequency pulse-
width-modulation (PWM) mode. Quiescent current for the
EL7584 is only 5mA when enabled, and since only the low
side MOSFET is used, switch drive current is minimized.
90% efficiency is achieved in most common application
operating conditions.
A functional block diagram with typical circuit configuration is
shown on previous page. Regulation is performed by the
PWM comparator which regulates the output voltage by
comparing a divided output voltage with an internal
reference voltage. The PWM comparator outputs its result to
the PWM logic. The PWM logic switches the MOSFET on
and off through the gate drive circuit. Its switching frequency
is external adjustable with a resistor from timing control pin
(R OSC ) to ground. The boost converter has 200kHz to
1.2MHz operating frequency range.
Start-Up
After V DDB reaches a threshold of about 2V, the power
MOSFET is controlled by the start-up oscillator, which
generates fixed duty-ratio of 0.5 - 0.7 at a frequency of
several hundred kilohertz. This will boost the output voltage,
providing the initial output current load is not too great
(<250mA).
When V DDB reaches about 3.7V, the PWM comparator
takes over the control. The duty ratio will be decided by the
multiple-input direct summing comparator, Max_Duty signal
(about 90% duty-ratio), and the Current Limit Comparator,
whichever is the smallest.
The soft-start is provided by the current limit comparator. As
the internal 12μA current source charges the external soft-
start capacitor, the peak MOSFET current is limited by the
voltage on the capacitor. This in turn controls the rising rate
of output voltage.
The regulator goes through the start-up sequence as well
after the EN signal is pulled to HI.
9
Steady-State Operation
When the output reaches the preset voltage, the regulator
operates at steady state. Depending on the input/output
condition and component, the inductor operates at either
continuous-conduction mode or discontinuous-conduction
mode.
In the continuous-conduction mode, the inductor current is a
triangular waveform and LX voltage a pulse waveform. In the
discontinuous-conduction mode, the inductor current is
completely ‘dried-out’ before the MOSFET is turned on
again. The input voltage source, the inductor, and the
MOSFET and output diode parasitic capacitors forms a
resonant circuit. Oscillation will occur in this period. This
oscillation is normal and will not affect the regulation.
At very low load, the MOSFET will skip pulse sometimes.
This is normal.
Current Limit
The MOSFET is current limited to <1.75Amps (nominal).
This restricts the maximum output current I OMAX based on
the following formula:
Δ L V IN
? 2 ?
where:
? Δ I L is the inductor peak-to-peak current ripple and is
decided by:
V IN D
L
? D is the MOSFET turn-on radio and is decided by:
D = ------------------------
V O
? F S is the switching frequency.
FN7317.2
February 4, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| AHA476M25E16B-F | CAP ALUM 47UF 25V 20% SMD |
| HMM24DRXH | CONN EDGECARD 48POS DIP .156 SLD |
| EL7584IR-T7 | IC CONV DC/DC 4-CHAN 24-TSSOP |
| AHA336M50E16B-F | CAP ALUM 33UF 50V 20% SMD |
| EL7584IR-T13 | IC CONV DC/DC 4-CHAN 24-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL7584IRZ-T7 | 功能描述:IC CONV DC/DC 4-CHAN 24-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| EL7585 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:TFT-LCD Power Supply |
| EL7585_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:TFT-LCD Power Supply |
| EL7585A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:TFT-LCD Power Supply |
| EL7585AILZ | 功能描述:IC POWER SUPPLY TFT-LCD 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。