参数资料
| 型号： | EL7641ILTZ-T13 |
| 厂商： | Intersil |
| 文件页数： | 12/19页 |
| 文件大小： | 0K |
| 描述： | IC BOOST REG DC/DC TFT-LCD 32QFN |
| 标准包装： | 2,500 |
| 应用： | 转换器，TFT，LCD |
| 输入电压： | 2.6 V ~ 5.5 V |
| 输出数： | 1 |
| 输出电压： | 5.5 V ~ 20 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
EL7640, EL7641, EL7642
The following table gives typical values (margins are
considered 10%, 3%, 20%, 10% and 15% on V IN , V O , L, f S
and I LMT :
TABLE 2.
For low ESR ceramic capacitors, the output ripple is
dominated by the charging and discharging of the output
capacitor. The voltage rating of the output capacitor should
be greater than the maximum output voltage.
V IN (V)
3.3
3.3
3.3
5
5
5
V O (V)
9
12
15
9
12
15
L (μH)
6.8
6.8
6.8
6.8
6.8
6.8
f S (MHz)
1.2
1.2
1.2
1.2
1.2
1.2
I OMAX (mA)
898
622
458
1360
944
694
NOTE: Capacitors have a voltage coefficient that makes their
effective capacitance drop as the voltage across them increases.
C OUT in the equation above assumes the effective value of the
capacitor at a particular voltage and not the manufacturer ’s stated
value, measured at zero volts.
Compensation
The EL7640, EL7641, EL7642 can operate in either P mode
or PI mode. Connecting COMP pin directly to V IN will enable
P mode; For better load regulation, use PI mode with a
2.2nF capacitor and a 180 ? resistor in series between
I LAVG = -------------
I LPK = I LAVG + -------- L
V RIPPLE = I LPK × ESR + ------------------------ × ---------------- × -----
V C f
Input Capacitor
The input capacitor is used to supply the current to the
converter. It is recommended that C IN be larger than 10 μ F.
The reflected ripple voltage will be smaller with larger C IN .
The voltage rating of input capacitor should be larger than
maximum input voltage.
Boost Inductor
The boost inductor is a critical part which influences the
output voltage ripple, transient response, and efficiency.
Value of 3.3 μ H to 10 μ H inductor is recommended in
applications to fit the internal slope compensation. The
inductor must be able to handle the following average and
peak current:
I O
1 – D
? I
2
Rectifier Diode
A high-speed diode is desired due to the high switching
frequency. Schottky diodes are recommended because of
their fast recovery time and low forward voltage. The rectifier
diode must meet the output current and peak inductor
current requirements.
Output Capacitor
The output capacitor supplies the load directly and reduces
the ripple voltage at the output. Output ripple voltage
consists of two components: the voltage drop due to the
inductor ripple current flowing through the ESR of output
capacitor, and the charging and discharging of the output
capacitor.
V O – V IN I O 1
O OUT S
12
COMP pin and ground. To improve the transient response,
either the resistor value can be increased or the capacitor
value can be reduced, but too high resistor value or too low
capacitor value will reduce loop stability.
Boost Feedback Resistors
As the boost output voltage, V BOOST , is reduced below 12V
the effective voltage feedback in the IC increases the ratio of
voltage to current feedback at the summing comparator
because R2 decreases relative to R1. To maintain stable
operation over the complete current range of the IC, the
voltage feedback to the FBB pin should be reduced
proportionally, as V BOOST is reduced, by means of a series
resistor-capacitor network (R7 and C7) in parallel with R1,
with a pole frequency (fp) set to approximately 10kHz. for C2
effective = 10μF and 4kHz for C2 (effective) = 30μF.
R7 = ((1/0.1 x R2) – 1/R1)^-1
C7 = 1/(2 x 3.142 x fp x R7)
Linear-Regulator Controllers (V ON and V OFF )
The EL7640, EL7641, EL7642 include 2 independent
linear-regulator controllers, in which there is one positive
output voltage (V ON ), and one negative voltage (V OFF ). The
V ON and V OFF linear-regulator controller function diagram,
application circuit and waveforms are shown in Figure 19
and Figure 20 respectively.
FN7415.2
February 22, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| GSA31DTKH-S288 | CONN EDGECARD 62POS .125 EXTEND |
| LT1121AHVIS8#PBF | IC REG LDO ADJ .15A 8-SOIC |
| UPJ1J101MPD | CAP ALUM 100UF 63V 20% RADIAL |
| GMA31DTKH-S288 | CONN EDGECARD 62POS .125 EXTEND |
| URZ1H101MPD | CAP ALUM 100UF 50V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL7641ILTZ-T7 | 功能描述:直流/直流开关调节器 EL7641ILTZ TFT-LCD D DC-DC W/INTEGRTD AMP RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| EL7642 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:TFT-LCD DC/DC with Integrated Amplifiers |
| EL7642AILTZ | 功能描述:LCD 驱动器 EL7642AILTZ TFT-LCD DC-DC W/INTEGRTD AMP RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| EL7642AILTZ-T13 | 功能描述:LCD 驱动器 EL7642AILTZ TFT-LCD DC-DC W/INTEGRTD AMP RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| EL7642AILTZ-T7 | 功能描述:LCD 驱动器 EL7642AILTZ TFT-LCD DC-DC W/INTEGRTD AMP RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。