参数资料
| 型号： | EL8100IWZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 2/14页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP 200MHZ R-R SOT23-6 |
| 标准包装： | 1 |
| 放大器类型： | 电压反馈 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 200 V/µs |
| 增益带宽积： | 100MHz |
| -3db带宽： | 200MHz |
| 电流 - 输入偏压： | 1.5µA |
| 电压 - 输入偏移： | 800µV |
| 电流 - 电源： | 2mA |
| 电流 - 输出 / 通道： | 65mA |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 5 V，±1.5 V ~ 2.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 标准包装 |
| 产品目录页面： | 1234 (CN2011-ZH PDF) |
| 其它名称： | EL8100IWZ-T7ADKR |
10
FN7103.9
September 14, 2010
VOUT = Maximum output voltage of the application
RLOAD = Load resistance tied to ground
ILOAD = Load current
By setting the two PDMAX equations equal to each other, we
can solve the output current and RLOAD to avoid the device
overheat.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, a good printed circuit
board layout is necessary for optimum performance. Lead
lengths should be as sort as possible. The power supply pin
must be well bypassed to reduce the risk of oscillation. For
normal single supply operation, where the VS- pin is
connected to the ground plane, a single 4.7F tantalum
capacitor in parallel with a 0.1F ceramic capacitor from VS+
to GND will suffice. This same capacitor combination should
be placed at each supply pin to ground if split supplies are to
be used. In this case, the VS- pin becomes the negative
supply rail.
For good AC performance, parasitic capacitance should be
kept to a minimum. Use of wire-wound resistors should be
avoided because of their additional series inductance. Use
of sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance that can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier’s inverting input pin is very important. The
feedback resistor should be placed very close to the
inverting input pin. Strip line design techniques are
recommended for the signal traces.
Typical Applications
Video Sync Pulse Remover
Many CMOS analog to digital converters have a parasitic
latch up problem when subjected to negative input voltage
levels. Since the sync tip contains no useful video
information and it is a negative going pulse, we can chop it
off. Figure 27 shows a gain of 2 connections for EL8100,
EL8101. Figure 28 shows the complete input video signal
applied at the input, as well as the output signal with the
negative going sync pulse removed.
Multiplexer
Besides the normal power-down usage, the ENABLE pin of
the EL8100 can be used for multiplexing applications.
Figure 29 shows two EL8100s with the outputs tied together,
driving a back terminated 75
Ω video load. A 2VP-P 2MHz
sine wave is applied to Amp A and a 1VP-P 2MHz sine wave
is applied to Amp B. Figure 30 shows the ENABLE signal
and the resulting output waveform at VOUT. Observe the
break-before-make operation of the multiplexing. Amp A is
on and VIN1 is passed through to the output when the
ENABLE signal is low and turns off in about 25ns when the
ENABLE signal is high. About 200ns later, Amp B turns on
and VIN2 is passed through to the output. The
break-before-make operation ensures that more than one
amplifier isn’t trying to drive the bus at the same time.
FIGURE 27. SYNC PULSE REMOVER
5V
1K
VOUT
VIN
75
Ω
+
-
75
Ω
1k
75
Ω
VS+
VS-
FIGURE 28. VIDEO SIGNAL
1.0V
0.5V
0V
1.0V
0.5V
0V
M = 10s/DIV
VOUT
VIN
FIGURE 29. TWO TO ONE MULTIPLEXER
+2.5V
1k
2MHz
75
Ω
+
-
1K
75
Ω
-2.5V
VOUT
75
Ω
1VP-P
B
+2.5V
1K
2MHz
+
-
1k
75
Ω
-2.5V
2VP-P
A
ENABLE
EL8100, EL8101
相关PDF资料 |
PDF描述 |
|---|---|
| EL8102IS-T13 | IC AMP SGL R-R 500MHZ 8-SOIC |
| EL8170FSZ-T7 | IC AMP INSTRU SGL R-R I/O 8-SOIC |
| EL8172FSZ-T7 | IC AMP INSTRU SGL R-R I/O 8-SOIC |
| EL8176FIZ-T7 | IC OP AMP SGL RRIO PREC 6-WLCSP |
| EL8178FWZ-T7 | IC OPAMP SGL R-R I/O SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL8101 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:200MHz Rail-to-Rail Amplifiers |
| EL8101IW-T7 | 功能描述:IC OP AMP 200MHZ R-R SOT23-5 RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1,000 系列:- 放大器类型:电压反馈 电路数:4 输出类型:满摆幅 转换速率:33 V/µs 增益带宽积:20MHz -3db带宽:30MHz 电流 - 输入偏压:2nA 电压 - 输入偏移:3000µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:带卷 (TR) |
| EL8101IW-T7A | 功能描述:高速运算放大器 200 MHz Rail to Rail RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| EL8101IWZ-T7 | 功能描述:运算放大器 - 运放 EL8101IWZ 200MHZ R2R AMP RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| EL8101IWZ-T7A | 功能描述:运算放大器 - 运放 EL8101IWZ 200MHZ R2R AMP RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。