参数资料
| 型号： | EL8178FWZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 13/13页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP SGL R-R I/O SOT23-6 |
| 标准包装： | 3,000 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.15 V/µs |
| 增益带宽积： | 266kHz |
| 电流 - 输入偏压： | 1pA |
| 电压 - 输入偏移： | 50µV |
| 电流 - 电源： | 55µA |
| 电流 - 输出 / 通道： | 31mA |
| 电压 - 电源，单路/双路(±)： | 2.4 V ~ 5.5 V，±1.2 V ~ 2.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 带卷 (TR) |
9
FN7504.7
May 14, 2008
Application Information
Introduction
The EL8178 is a rail-to-rail input and output (RRIO),
micropower, precision, single supply op amp with an enable
feature. This amplifier is designed to operate from single
supply (2.4V to 5.5V) or dual supply (±1.2V to ±2.75V) while
drawing only 55A of supply current.The device achieves
rail-to-rail input and output operation while eliminating the
drawbacks of many conventional RRIO op amps.
Rail-to-Rail Input
The PFET input stage of the EL8178 has an input
common-mode voltage range that includes the negative and
positive supplies without introducing offset errors or
degrading performance like some existing rail-to-rail input
op amps. Many rail-to-rail input stages use two differential
input pairs: a long-tail PNP (or PFET) and an NPN (or
NFET). Severe penalties result from using this topology. As
the input signal moves from one supply rail to the other, the
op amp switches from one input pair to the other causing
changes in input offset voltage and an undesired change in
the input offset current’s magnitude and polarity.
The EL8178 achieves rail-to-rail input performance without
sacrificing important precision specifications and without
degrading distortion performance. The EL8178's input offset
voltage exhibits a smooth behavior throughout the entire
common-mode input range.
Rail-to-Rail Output
A pair of complementary MOSFET devices achieve rail-to-rail
output swing. The NMOS sinks current to swing the output in
the negative direction, while the PMOS sources current to
swing the output in the positive direction. The EL8178 with a
100k
Ω load swings to within 3mV of the supply rails.
Results of Overdriving the Output
Caution should be used when overdriving the output for long
periods of time. Overdriving the output can occur in three ways:
1. The input voltage times the gain of the amplifier exceeds the
supply voltage by a large value.
2. The output current required is higher than the output stage
can deliver.
3. Operating the device in slew rate limit. These conditions can
result in a shift in the Input Offset Voltage (VOS) as much as
1V/hr of exposure under these conditions.
Enable/Disable Feature
The EL8178 features an active low EN pin that when pulled
up to at least 2V, disables the output and drops the ICC to a
3A. The EN pin has an internal pull-down, so an undriven
pin pulls to the negative rail, thereby enabling the op amp by
default. For applications where the EN pin is not being used,
it is recommended that the EN pin be permanently tyed to
ground.
The high impedance output during disable allows for
connecting multiple EL8178s together to implement a Mux
Amp. The outputs are connected together and activating the
appropriate EN pin selects the desired channel. If utilizing
non-unity gain op amp configurations, then the loading
Pin Descriptions
SO PIN
NUMBER
SOT-23 PIN
NUMBER
PIN NAME
EQUIVALENT
CIRCUIT
DESCRIPTION
1
NC
No internal connection
2
4
IN-
Circuit 1
Amplifier’s inverting input
3
IN+
Circuit 1
Amplifier’s non-inverting input
4
2
V-
Circuit 4
Negative power supply
5
NC
No internal connection
6
1
OUT
Circuit 3
Amplifier’s output
7
6
V+
Circuit 4
Positive power supply
85
EN
Circuit 2
Amplifier’s enable pin with internal pull-down; Logic “1” selects the disabled
state; Logic “0” selects the enabled state.
EN
OUT
CIRCUIT 3
CIRCUIT 2
CAPACITIVELY
COUPLED
ESD CLAMP
CIRCUIT 4
V+
V-
IN-
V+
V-
CIRCUIT 1
IN+
EL8178
相关PDF资料 |
PDF描述 |
|---|---|
| EL8188IW-T7A | IC OPAMP SGL MICROPOWER SOT23-6 |
| EL8300IUZ-T13 | IC AMP TRIPLE R-R 200MHZ 16-QSOP |
| EL8302IU-T13 | IC AMP TRIPLE R-R 500MHZ 16-QSOP |
| EL8401ISZ | IC OP AMP 200MHZ R-R 14-SOIC |
| EL8403IUZ-T13 | IC AMP QUAD R-R 500MHZ 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL8178FWZ-T7A | 功能描述:IC OPAMP SGL R-R I/O SOT23-6 RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| EL8178ISZ | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Micropower Single Supply Rail-to-Rail Input-Output Precision Op Amp |
| EL8178ISZ-T13 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Micropower Single Supply Rail-to-Rail Input-Output Precision Op Amp |
| EL8178ISZ-T7 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Micropower Single Supply Rail-to-Rail Input-Output Precision Op Amp |
| EL817A | 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:4 PIN DIP PHOTOTRANSISTOR |
发布紧急采购，3分钟左右您将得到回复。