参数资料
| 型号： | EL9110IU |
| 厂商： | Intersil |
| 文件页数： | 8/10页 |
| 文件大小： | 0K |
| 描述： | IC RCVR/EQLZR DIFF 150MHZ 16QSOP |
| 标准包装： | 97 |
| 类型： | 接收器 |
| 驱动器/接收器数： | 0/1 |
| 规程： | 双绞线 |
| 电源电压： | 5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
| 产品目录页面： | 1239 (CN2011-ZH PDF) |
7
FN7305.5
November 30, 2007
operation it is anticipated the X2 mode will be selected and
the output load will be back matched. A unity gain to the
output load will then be achieved with a gain control voltage
of about 0.35V. This allows the gain to be trimmed up or
down by 6dB to compensate for any gain/loss errors that
affect the contrast of the video signal. Figure 12 shows an
example plot of the gain to the load with gain control voltage.
Circuit and Layout Recommendation
The interconnection cable is a transmission line therefore for
proper function it should be treated like transmission line, a
refection-free termination is necessary.
A reflection-free termination is a real "ohmic" resistor with as
less as possible reactive parasitic.
The traces of the layout, up to the point where of the
termination resistor placed, are part of the transmission line
which also includes the cable's connector. A connector with
a better controlled impedance is an obligation for good
picture quality. The termination resistor should be placed
close to the inputs of the device's pins (pin 3 and pin 4.) The
small capacitance differential and common mode
capacitance of the input pins of the device makes it possible
to connect parallel to the termination resistor.
The cable will work as an antenna for all the RF spectrum
which is "in the air" where the cable is used. The spectrum,
particularly its common mode components, could and will
contain high energy level of transients which are above the
built-in protection level of the device and easily could
damage its inputs. Using a transient protection circuit
according to the given application is recommended.
Since the used signal's bandwidth is in the range of 100MHz,
for layout and power supply bypassing the roles of RF
design should be applied.
The following picture is taken from the DB9110 demo-
board's layout. For better visibility the ground plain is
removed.
The ground plane is shown in Figure 14.
00.8
VGAIN
0.4
1.0
2.0
1.8
1.4
1.0
0.6
0.4
GAIN
(V)
0.6
0.2
1.6
1.2
0.8
FIGURE 12. VARIATION OF GAIN WITH GAIN CONTROL
VOLTAGE
0
10
20
30
40
50
60
70
0.01M
0.10M
1M
10M
100M
FREQUENCY (Hz)
A
T
TE
NU
A
T
ION
(
d
B)
FIGURE 13. CAT-5 CABLE ATTENUATION CHARACTERISTICS
300M
200M
100M
50M
FIGURE 14. DEMO BOARD LAYOUT
EL9110
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1293BEEG+ | IC ADC 12BIT 250KSPS 24-QSOP |
| MS3106F20-14P | CONN PLUG 5POS STRAIGHT W/PINS |
| MC10SX1190DTR2G | IC DRIVER COAX CABLE 20-TSSOP |
| MAX1264ACEG+ | IC ADC 12BIT 400KSPS 24-QSOP |
| VE-2TN-MX-F4 | CONVERTER MOD DC/DC 18.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL9110IUE9049 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| EL9110IUE9049-T7 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| EL9110IU-T13 | 功能描述:IC DIFF RCVR/EQUALZR SGL 16-QSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| EL9110IU-T7 | 功能描述:IC RCVR/EQLZR DIFF 150MHZ 16QSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| EL9110IUZ | 功能描述:总线接收器 EL9110IUZ DIFFRNTLCV R/EQUALIZER RoHS:否 制造商:Texas Instruments 接收机数量:4 接收机信号类型:Differential 接口类型:EIA/TIA-422-B, V.11 工作电源电压:3.3 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:TSSOP-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。