- 您现在的位置：买卖IC网 > PDF目录10840 > EL9200IL-T7 (Intersil)IC AMP VCOM PROGRAMMABLE 12-DFN PDF资料下载
参数资料
| 型号： | EL9200IL-T7 |
| 厂商： | Intersil |
| 文件页数： | 4/15页 |
| 文件大小： | 0K |
| 描述： | IC AMP VCOM PROGRAMMABLE 12-DFN |
| 标准包装： | 1,000 |
| 应用： | TFT-LCD 面板：VCOM 驱动器 |
| 输出类型： | 满摆幅 |
| 电路数： | 1 |
| -3db带宽： | 44MHz |
| 转换速率： | 80 V/µs |
| 电流 - 电源： | 3.8mA |
| 电流 - 输出 / 通道： | 65mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-VFDFN 裸露焊盘 |
| 供应商设备封装： | 12-DFN-EP（4x4） |
| 包装： | 带卷 (TR) |
12
FN7438.1
October 30, 2008
Non-Volatile Memory (EEPROM)
Programming
When the CTL pin exceeds 4.9V, the non-volatile
programming cycle will be activated. The CTL signal needs
to remain above 4.9V for more than 200s. The level and
timing needed to program the non-volatile memory is given
below. It then takes a maximum of 100ms for the
programming to be completed inside the device (see PT
specification in Table Electrical Specifications on page 3.
FIGURE 28. EEPROM PROGRAMMING
Amplifiers’ Operating Voltage, Input, and Output
The amplifiers are specified with a single nominal supply
voltage from 5V to 15V or a split supply with its total range
from 5V to 15V. Correct operation is guaranteed for a supply
range of 4.5V to 16.5V. Most amplifier specifications are
stable over both the full supply range and operating
temperatures of -40°C to +85°C. Parameter variations with
operating voltage and/or temperature are shown in the See
The input common-mode voltage range of the amplifiers
extends 500mV beyond the supply rails. The output swings
of the those typically extend to within 100mV of positive and
negative supply rails with load currents of 5mA. Decreasing
load currents will extend the output voltage range even
closer to the supply rails. Figure 27 shows the input and
output waveforms for the device in the unity-gain
configuration. Operation is from 5V supply with a 1k
Ω load
connected to GND. The input is a 10VP-P sinusoid. The
output voltage is approximately 9.8VP-P.
FIGURE 29. OPERATION WITH RAIL-TO-RAIL INPUT AND
OUTPUT
Short-Circuit Current Limit
The amplifiers will limit the short circuit current to ±180mA if
the output is directly shorted to the positive or the negative
supply. If an output is shorted indefinitely, the power
dissipation could easily increase such that the device may
be damaged. Maximum reliability is maintained if the output
continuous current never exceeds ±65mA. This limit is set by
the design of the internal metal interconnects.
Output Phase Reversal
The amplifiers are immune to phase reversal as long as the
input voltage is limited from VS- -0.5V to VS+ +0.5V.
Figure 28 shows a photo of the output of the device with the
input voltage driven beyond the supply rails. Although the
device's output will not change phase, the input's
overvoltage should be avoided. If an input voltage exceeds
supply voltage by more than 0.6V, electrostatic protection
diodes placed in the input stage of the device begin to
conduct and over-voltage damage could occur.
FIGURE 30. OPERATION WITH BEYOND-THE-RAILS INPUT
Unused Amplifiers
It is recommended that any unused amplifiers in a dual and
a quad package be configured as a unity gain follower. The
inverting input should be directly connected to the output
and the non-inverting input tied to the ground plane.
Power Supply Bypassing and Printed Circuit
Board Layout
The amplifiers can provide gain at high frequency. As with
any high-frequency device, good printed circuit board layout
is necessary for optimum performance. Ground plane
construction is highly recommended, lead lengths should be
as short as possible and the power supply pins must be well
bypassed to reduce the risk of oscillation. For normal
operation, a 0.1F ceramic capacitor should be placed from
VS to pin to GND. A 4.7F tantalum capacitor should then be
connected in parallel, placed in the region of the amplifier.
CTLPT
TIME
4.9V
CTL VOLTAGE
OUT
P
UT
IN
P
U
T
5V
10s
AV = 1
VS = 5V
TA = +25°C
VIN = 10VP-P
1V
10s
VS = 2.5V
AV = 1
TA = +25°C
VIN = 6VP-P
EL9200, EL9201, EL9202
相关PDF资料 |
PDF描述 |
|---|---|
| EL9200IL-T13 | IC AMP VCOM PROGRAMMABLE 12-DFN |
| VI-24W-IV-F2 | CONVERTER MOD DC/DC 5.5V 150W |
| MAX5150BEEE+T | IC DAC 13BIT DUAL LP SER 16-QSOP |
| MAX5151BEEE+T | IC DAC 13BIT DUAL LP SER 16-QSOP |
| EL9202IL-T13 | IC AMP VCOM PROGRAMMABLE 24-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL9200ILZ | 功能描述:IC AMP SGL PROGR TFT-LCD 12-DFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| EL9200ILZ-T13 | 功能描述:IC AMP VCOM PROGRAMMABLE 12-DFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
| EL9200ILZ-T7 | 功能描述:IC AMP VCOM PROGRAMMABLE 12-DFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
| EL9201 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Programmable VCOM |
| EL9201IL | 功能描述:IC AMP VCOM PROGRAMMABLE 24-QFN RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。