收藏本站
参数资料
型号： EPC1064
厂商： Electronic Theatre Controls, Inc.
英文描述： Configuration Devices for SRAM-Based LUT Devices
中文描述： 配置SRAM器件基于LUT的器件
文件页数： 16/28页
文件大小： 380K
代理商： EPC1064
16
Altera Corporation
Configuration Devices for ACEX, APEX, FLEX & Mercury Devices Data Sheet
Table5
describes the pin functions of all configuration devices during
FLEX 8000 device configuration.
Notes:
(1)
(2)
(3)
This package is available for EPC1, EPC1441, EPC1213, EPC1064, and EPC1064V devices only.
This package is available for EPC1441, EPC1064, and EPC1064V devices only.
The EPC1441, EPC1064, and EPC1064V devices do not support data cascading. The EPC1 and EPC1213 devices
support data cascading for FLEX 8000 devices.
f
For more information on FLEX 8000 device configuration, see the
following documents:
I
Table 5. Configuration Device Pin Functions During FLEX 8000 Device Configuration
Pin Name
Pin Number
Pin
Type
Description
8-Pin
PDIP
(1)
20-Pin
PLCC
32-Pin
TQFP
(2)
DATA
1
2
31
Output
Serial data output. The
DATA
pin is tri-stated before
configuration when the
nCS
pin is high and after the
configuration device finishes sending its configuration
data. This operation is independent of the device
’
s
position in the cascade chain.
DCLK
2
4
2
Input
DCLK
is a clock input when using EPC1, EPC1213,
EPC1064, and EPC1064V configuration devices. Rising
edges on
DCLK
increment the internal address counter
and present the next bit of data to the
DATA
pin. The
counter is incremented only if the
OE
input is held high,
the
nCS
input is held low, and all configuration data has
not been transferred to the target device.
OE
3
8
7
Open-
Drain
I/O
Input
Output enable (active high) and reset (active low). A low
logic level resets the address counter. A high logic level
enables
DATA
and permits the address counter to count.
nCS
(3)
4
9
10
Chip-select input (active low). A low input allows
DCLK
to
increment the address counter and enables
DATA
.
nCASC
6
12
15
Output
Cascade-select output (active low). This output goes low
when the address counter has reached its maximum
value. The
nCASC
output is usually connected to the
nCS
input of the next device in a configuration chain, so the
next
DCLK
clocks data out of the next device.
Power pin.
Ground Ground pin. A 0.2-
μ
F decoupling capacitor must be
placed between the
VCC
and
GND
pins.
VCC
7, 8
5
20
10
27
12
Power
GND
相关PDF资料
PDF描述
EPC1064V Configuration Devices for SRAM-Based LUT Devices
EPC1213 Configuration Devices for SRAM-Based LUT Devices
EPC1441 Configuration Devices for SRAM-Based LUT Devices
EPC1064 Configuration Devices for ACEX, APEX, FLEX & Mercury Devices
EPC1064V Configuration Devices for ACEX, APEX, FLEX & Mercury Devices
相关代理商/技术参数
参数描述
EPC1064LC20 功能描述:FPGA-配置存储器 IC - Ser. Config Mem Flash 64Kb 6 MHz RoHS:否 制造商:Altera Corporation 存储类型:Flash 存储容量:1.6 Mbit 工作频率:10 MHz 电源电压-最大:5.25 V 电源电压-最小:3 V 电源电流:50 uA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PLCC-20
EPC1064LC-20 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM
EPC1064LI20 功能描述:IC CONFIG DEVICE 65KBIT 20-PLCC RoHS:否 类别:集成电路 (IC) >> 存储器 - 用于 FPGA 的配置 Proms 系列:EPC 产品变化通告:Product Discontinuation 28/Jul/2010 标准包装:98 系列:- 可编程类型:OTP 存储容量:300kb 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-TSOP 包装:管件
EPC1064LI-20 制造商:未知厂家 制造商全称:未知厂家 功能描述:Configuration EPROM
EPC1064PA1 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
发布紧急采购，3分钟左右您将得到回复。