- 您现在的位置：买卖IC网 > PDF目录97931 > EPM7512AEQC208-12 PDF资料下载
参数资料
| 型号： | EPM7512AEQC208-12 |
| 文件页数： | 14/60页 |
| 文件大小： | 1041K |
| 代理商： | EPM7512AEQC208-12 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Altera Corporation
21
MAX 7000A Programmable Logic Device Data Sheet
Programmable
Speed/Power
Control
MAX 7000A devices offer a power-saving mode that supports low-power
operation across user-defined signal paths or the entire device. This
feature allows total power dissipation to be reduced by 50% or more
because most logic applications require only a small fraction of all gates to
operate at maximum frequency.
The designer can program each individual macrocell in a MAX 7000A
device for either high-speed (i.e., with the Turbo BitTM option turned on)
or low-power operation (i.e., with the Turbo Bit option turned off). As a
result, speed-critical paths in the design can run at high speed, while the
remaining paths can operate at reduced power. Macrocells that run at low
power incur a nominal timing delay adder (tLPA) for the tLAD, tLAC, tIC,
tEN, tSEXP, tACL, and tCPPW parameters.
Output
Conguration
MAX 7000A device outputs can be programmed to meet a variety of
system-level requirements.
MultiVolt I/O Interface
The MAX 7000A device architecture supports the MultiVolt I/O interface
feature, which allows MAX 7000A devices to connect to systems with
differing supply voltages. MAX 7000A devices in all packages can be set
for 2.5-V, 3.3-V, or 5.0-V I/O pin operation. These devices have one set of
VCC pins for internal operation and input buffers (VCCINT), and another
set for I/O output drivers (VCCIO).
The VCCIO pins can be connected to either a 3.3-V or 2.5-V power supply,
depending on the output requirements. When the VCCIO pins are
connected to a 2.5-V power supply, the output levels are compatible with
2.5-V systems. When the VCCIO pins are connected to a 3.3-V power
supply, the output high is at 3.3 V and is therefore compatible with 3.3-V
or 5.0-V systems. Devices operating with VCCIO levels lower than 3.0 V
incur a slightly greater timing delay of tOD2 instead of tOD1. Inputs can
always be driven by 2.5-V, 3.3-V, or 5.0-V signals.
Table 9 describes the MAX 7000A MultiVolt I/O support.
Table 9. MAX 7000A MultiVolt I/O Support
VCCIO Voltage
Input Signal (V)
Output Signal (V)
2.5
3.3
5.0
2.5
3.3
5.0
2.5
vvvv
3.3
vvv
vv
相关PDF资料 |
PDF描述 |
|---|---|
| EPM7512AEQC208-7 | |
| EPM7512AEQI208-10 | |
| EPM7512AETC144-10 | |
| EPM7512AETC144-12 | |
| EPM7512AETC144-7 | |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EPM7512AEQC208-12N | 功能描述:CPLD - 复杂可编程逻辑器件 CPLD - MAX 7000 512 Macro 176 IOs RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| EPM7512AEQC208-7 | 功能描述:CPLD - 复杂可编程逻辑器件 CPLD - MAX 7000 512 Macro 176 IOs RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| EPM7512AEQC208-7N | 功能描述:CPLD - 复杂可编程逻辑器件 CPLD - MAX 7000 512 Macro 176 IOs RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| EPM7512AEQI208-10 | 功能描述:CPLD - 复杂可编程逻辑器件 CPLD - MAX 7000 512 Macro 176 IOs RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| EPM7512AEQI208-10N | 功能描述:CPLD - 复杂可编程逻辑器件 CPLD - MAX 7000 512 Macro 176 IOs RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
发布紧急采购，3分钟左右您将得到回复。