- 您现在的位置：买卖IC网 > PDF目录169797 > EQ2660-7P (POWER-ONE INC) 2-OUTPUT 106 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | EQ2660-7P |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | 2-OUTPUT 106 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | METAL, CASE Q01, MODULE |
| 文件页数： | 6/25页 |
| 文件大小： | 747K |
| 代理商： | EQ2660-7P |
Cassette Style
DC-DC Converters
Q Series
Edition 5/5.2000
14/25
Auxilary Functions
i Inhibit for Remote On and Off
Note: If this function is not actively used, the inhibit pin 28
must be interconnected with the negative input pin 32 to en-
able the output(s). A non-connected pin 28 will be inter-
preted by the internal logic as an active inhibit signal and
therefore output(s) will remain disabled: Fail safe function.
An inhibit input enables (logic low, pull down) or disables
(logic high, pull up) the output if a logic signal e.g. TTL,
CMOS is applied. In systems consisting of several units,
this feature may be used, for example, to control the activa-
tion sequence of the converters by means of logic signals,
or to allow the unit's source for a proper start up before full
load is applied (e.g. in combination with LT units).
Table 6: Inhibit characteristics
Characteristics
Conditions
min typ max
Unit
Uinh Inhibit
Uo = on Ui min...Ui max
–100
0.8
V DC
voltage
Uo = off
TC min...TC max
2.4
100
Iinh
Inhibit current
Uinh = –50 V
–500
A
Uinh =0 V
–40
Uinh = 50 V
+500
Uinh = 100 V
+1000
i
Vi–
Vi+
Vo–
S–
Ui
Io
Uo
RL
Ii
Iinh
Uinh
Vo–
Vo+
S+
28
30
32
26
14
10
8
6
4
12
06091
Fig. 18
Definition of input and output parameters
0
tr
Ui
t
0.8
on
off
Uinh [V]
2.4
0.1
Uo/Uo normal
tf
td on
0.99
1.01
06092
Fig. 19
Output response as a function of input voltage (on/off
switching) or inhibit control
Output Response
The output response when enabling and disabling the out-
put by the inhibit input is shown in the following figure.
Table 7: Output response time with outputs resistively loaded and R-input and P option not used
BQ, CQ, GQ
DQ, EQ
Characteristics
Conditions
min
typ
max
min
typ
max
Unit
td on
Turn-on delay time
Ui = 0 → Ui min, RL = Uo nom/0.5 Io nom
5
850
ms
Ui = 0 → Ui nom, RL = Uo nom/Io nom
3.5
250
tr
Output voltage rise time
Ui = 0 → Ui nom, RL = Uo nom/Io nom
2.5
Ui inh = 2.4 → 0.8 V, RL = Uo nom/Io nom
tf
Output voltage fall time
Ui = Ui nom → 0, RL = Uo nom/Io nom
33
Ui inh = 0.8 → 2.4 V, RL = Uo nom /Io nom
Current Sharing (T Function)
The current sharing facility should be used where several
units are to be operated in parallel for high reliability n+1
redundant systems or in order to provide higher output
powers. Using this feature reduces the stress on the units
and further improves the reliability of the system.
Interconnection of the current sharing terminals T causes
the units to share the output current to the average of all
units. The current tolerance of each unit is approx.
±20% of
the sum of its nominal output currents
Io1 nom + Io2 nom.
In n+1 redundant systems, a failure of a single unit will not
lead to a system failure if the outputs are decoupled by di-
odes. See also
Sense Lines.
Since the voltage on the T pin is referenced to the sense pin
S–, the installer must ensure that the S– pins of all units are
at the same electrical potential, i.e. voltage drops
>50 mV
across the connection lines between these pins shall be
avoided.
BQ...GQ 2000 DC-DC converters with outputs connected
in series can also be paralleled with current sharing, if pins
Vo1– of all units are connected together. See
Sense Lines.
If the output voltages are programmed to a voltage other
than
Uo nom by means of the R pin or option P, the outputs
should be adjusted individually within a tolerance of
±1%.
The current sharing will be less accurate when operating
with dynamic loads.
Important: For applications using the hot plug-in capa-
bilities, dynamic output voltage changes during the plug-
in/plug-out cycles must be considered.
相关PDF资料 |
PDF描述 |
|---|---|
| CQ92M | epoxy molded silicon Triacs |
| CQ92N | epoxy molded silicon Triacs |
| CQY80N(G) | 1 CHANNEL TRANSISTOR OUTPUT OPTOCOUPLER |
| CQY80SM | 1 CHANNEL TRANSISTOR OUTPUT OPTOCOUPLER |
| CR102J4RS215QF7 | ROCKER SWITCH, SPST, LATCHED, PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EQ2660-7R | 制造商:Power-One 功能描述:DC/DC PS DUAL-OUT 24V 5.1A 132W - Bulk |
| EQ2660-7RREP | 制造商:Power-One 功能描述: |
| EQ2660-9R | 功能描述:EURO-CASSETTE 106W 2X 24V RoHS:否 类别:电源 - 外部/内部（非板载） >> DC DC Converters 系列:* 标准包装:1 系列:Quint 类型:隔离 输入电压:24V 输出:24V 输出数:1 输出 - 1 @ 电流（最大）:24 VDC @ 50A 输出 - 2 @ 电流（最大）:- 输出 - 3 @ 电流（最大）:- 输出 - 4 @ 电流（最大）:- 功率（瓦特）:1200W 安装类型:底座安装 工作温度:0°C ~ 40°C 效率:- 封装/外壳:模块 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H（110mm x 231mm x 156mm） 包装:散装 电源（瓦特）- 最大:1200W 批准:- 其它名称:277-69722866365-NDQUINT-BAT/24DC/12AH |
| EQ30 | 制造商:FERROXCUBE 制造商全称:Ferroxcube International Holding B.V. 功能描述:EQ cores and accessories |
| EQ30-3C94 | 制造商:FERROXCUBE 制造商全称:Ferroxcube International Holding B.V. 功能描述:EQ cores and accessories |
发布紧急采购，3分钟左右您将得到回复。