- 您现在的位置：买卖IC网 > Datasheet目录324 > ER3-8M (TechTools)EMULATOR EPROM ECONOROM III 8MEG Datasheet资料下载
参数资料
| 型号： | ER3-8M |
| 厂商： | TechTools |
| 文件页数： | 22/24页 |
| 文件大小： | 0K |
| 描述： | EMULATOR EPROM ECONOROM III 8MEG |
| 标准包装： | 1 |
| 系列： | EconoROM™ III |
| 类型： | 存储器 |
| 适用于相关产品： | EPROMs |
| 所含物品： | ER3 EconoROM III 仿真器，线缆（菊花链、LPT 和目标）等 |
| 配用： | CBL08-25-ND - 25 FT DOWNLOAD CABLE UPGRADE C32D-6-ND - 6" TARGET CABLE IDC TO 32PIN DIP C28D-6-ND - 6" TARGET CABLE IDC TO 28PIN DIP PS-RT1-ND - EXTERNAL PWR SUPPLY |
| 其它名称： | ER38M |
FAQs
Can I use EconoROM III on a 3V target?
YES, but you will need an external power supply. Connect 5VDC at 300ma or greater to the emulator’s
external power connector. External power supplies are available form TechTools.
What is the lowest target voltage supported?
Econo ROM III was designed to support 3.0V to 5.0V targets. However, it CAN support lower voltage
targets within limits. Three things set the lower limit; Logic INPUT thresholds, Vout HIGH from the
emulator, and the target isolation threshold.
-
-
-
Logic INPUT Thresholds. Econo ROM III will accept a Vin HIGH minimum of 1.5Volts. Your
target MUST produce at least 1.5V for logic HIGHs. Most logic down to about 2V can meet this
requirement.
Vout HIGH levels: Your target must tolerate logic HIGHs from the emulator data lines of
3.2Volts. This depends entirely on your target design.
Target Isolation Threshold: To allow safe target power cycling,, Econo ROM III constantly
monitors the target’s voltage. When it detects that the target voltage has dropped below a fixed
threshold, it assumes the target is powering down so it turns off its output buffers to avoid leaking
current into the target. It also asserts reset and turns the STATUS LED RED. If the emulator did
NOT provide this safety feature, it could start reverse biasing devices on the target, potentially
causing damage. Even if the target were not damaged, the current leakage could prevent the target
from properly powering down. This could prevent the reset circuitry from operating. This cut-off
threshold is approximate 2.7 to 2.8V.
Bottom line: You CAN emulate lower voltage targets as long as you can tolerate 3.2V on your data bus,
your target provides logic highs of at least 1.5V and our low voltage cut-off circuit does not kick-in.
How accurate are EconoROM III’s voltage readings?
The readings are typically accurate to +- 150mv.
Can EconoROM III emulate FLASH devices?
YES and NO. The emulator does NOT support target writes. However, if your target doesn’t need to
WRITE to the emulator, then emulation is possible as long as the pin-outs match or are adapted. EPROM
and FLASH devices have very similar pin-outs but vary slightly to allow for the extra write/program line
required by the FLASH device. Econo ROM III is compatible with the timing requirements of both
EPROM and FLASH devices.
Econo ROM III User’s Manual
18
Copyright ? 2000, TechTools
相关PDF资料 |
PDF描述 |
|---|---|
| ESF2424 | FRAME SWING ECLIPSE 19.25X19" |
| ESF3024 | FRAME SWING ECLIPSE 24.5X19" |
| ESF3624 | FRAME SWING ECLIPSE 29.75X19" |
| ESP1212 | PANEL STEEL SWING 12X12" WHT |
| ESP1612 | PANEL STEEL SWING 16X12" WHT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ER-3997 | 功能描述:烙铁 SOLDERING TIP RoHS:否 制造商:Weller 产品:Soldering Stations 类型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大温度:+ 850 F 电缆类型:US Cord Included |
| ER-3998 | 功能描述:烙铁 SOLDERING TIP RoHS:否 制造商:Weller 产品:Soldering Stations 类型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大温度:+ 850 F 电缆类型:US Cord Included |
| ER-3999 | 功能描述:烙铁 SOLDERING TIP RoHS:否 制造商:Weller 产品:Soldering Stations 类型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大温度:+ 850 F 电缆类型:US Cord Included |
| ER39R37CA | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:REFLECTOR FOR E3T |
| ER3A | 制造商:TAYCHIPST 制造商全称:Shenzhen Taychipst Electronic Co., Ltd 功能描述:SURFACE MOUNT SUPER FAST RECTIFIERS |
发布紧急采购，3分钟左右您将得到回复。