- 您现在的位置：买卖IC网 > PDF目录18719 > EVAL-433-KF (Linx Technologies Inc)KIT EVAL KEYFOB 433 MHZ 5 BUTTON PDF资料下载
参数资料
| 型号： | EVAL-433-KF |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL KEYFOB 433 MHZ 5 BUTTON |
| 标准包装： | 1 |
| 类型： | 发射器 |
| 频率： | 433MHz |
| 适用于相关产品： | Linx OEM 模块 |
| 已供物品： | 板，2 个发射器，2 个接收器，天线，电池，2 个连接器，文档 |
| 其它名称： | EVAL-433-KEY5 EVAL-433-KEY5-ND |
CONTENTION CONSIDERATIONS
It is important to understand that only one transmitter at a time can be activated
within a reception area. While the transmitted signal consists of encoded digital
data, only one carrier of any particular frequency can occupy airspace without
contention at any given time. If two transmitters are activated in the same area
at the same time, then the signals will interfere with each other and the decoder
will not see a valid transmission, so it will not take any action.
BATTERY REPLACEMENT
The remote unit utilizes a standard CR2032 lithium
button cell. In normal use, it will provide 1 to 2 years of
operation. Access for replacement is accomplished by
gently prying apart the two halves of the keyfob at the
seam (fingernails will do for this). Once the unit is
COMPLIANCE REQUIREMENTS
The CMD-KEY#-*** has been pre-certified by Linx Technologies for FCC Part 15
and Industry Canada RSP-100 compliance. The 433.92MHz version has also
been tested for CE compliance for use in the European Union. The 315MHz and
418MHz versions are not legal for use in Europe.
LABELING / INSTRUCTION REQUIREMENTS
The CMD-KEY#-*** Keyfob Transmitter has already been labeled in accordance
with FCC, Industry Canada, and CE regulations in effect as of the date of this
document. No further labeling of the unit is needed; however, it is necessary to
include the following statement in the end product’s instruction manual or insert
card for FCC compliance. Industry Canada only requires the shaded portion. EU
does not require a statement.
open, remove the battery by sliding it out from beneath
the retainer.
There may be the risk of explosion if the battery is
replaced by the wrong type. Replace it with the same
type of battery while observing the polarity shown in
the adjacent figure.
ASSEMBLY DIAGRAM
Figure 5: CMD-KEY#-*** Assembly
Page 4
+
Battery
Figure 4: Battery Access
INSTRUCTION TO THE USER
This device complies with Part 15 of the FCC Rules.
Operation of this device is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a Class B
computing device, pursuant to FCC Rules. In order to maintain compliance with
FCC regulations, shielded cables must be used with this equipment. Operation
with non-approved equipment or unshielded cables is likely to result in
interference to radio and TV reception. The user is cautioned that changes and
modifications made to the equipment without the approval of manufacturer
could void the user’s authority to operate this equipment.
Place the above statement in the instruction manual or insert card.
Page 5
相关PDF资料 |
PDF描述 |
|---|---|
| CR8401-1000 | TRANSFORMER CURRENT GENERAL PURP |
| 2540B | OSCOPE 60MHZ 1GSA/S DGTL STORAGE |
| CR8348-2000-F | TRANSFORMER CURRENT HI FREQUENCY |
| CR8448-2000-F | TRANSFORMER CURRENT HI FREQUENCY |
| EVAL-418-LT | KIT EVAL FOR LT SERIES 418MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-433-KH | 功能描述:KIT BASIC EVAL 433MHZ KH SERIES RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:KH 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| EVAL-433-KH2 | 功能描述:射频开发工具 KH2 Basic Eval System 433MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| EVAL-433-LC | 功能描述:射频开发工具 LC Basic Eval System 433MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| EVAL-433-LC-S | 功能描述:KIT BASIC EVAL 433MHZ LC SERIES RoHS:否 类别:RF/IF 和 RFID >> 过时/停产零件编号 系列:LC 标准包装:1 系列:- 类型:用于 200/300 系列的欧盟开发套件 适用于相关产品:Zensys RF 模块 所含物品:开发板，模块，编程器，软件，线缆，电源 其它名称:703-1019Q3225667 |
| EVAL-433-LR | 功能描述:射频开发工具 LR Basic Eval System 433MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。