- 您现在的位置：买卖IC网 > PDF目录18719 > EVAL-869-ES (Linx Technologies Inc)KIT EVAL BASIC 869MHZ ES SERIES PDF资料下载
参数资料
| 型号： | EVAL-869-ES |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 7/11页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL BASIC 869MHZ ES SERIES |
| 标准包装： | 1 |
| 系列： | ES |
| 类型： | 发射器，接收器 |
| 频率： | 869MHz |
| 适用于相关产品： | Linx OEM 模块 |
| 已供物品： | 2 个板，2 个发射器，2 个接收器，2 个连接器，2 根天线，电池，文档 |
PAD LAYOUT
The following pad layout diagram is designed to facilitate both hand and
automated assembly.
0.065"
0.610"
0.070"
0.100"
Figure 13: Recommended PCB Layout
PRODUCTION GUIDELINES
AUTOMATED ASSEMBLY
For high-volume assembly, most users will want to auto-place the modules. The
modules have been designed to maintain compatibility with reflow processing
techniques; however, due to the their hybrid nature, certain aspects of the
assembly process are far more critical than for other component types.
Following are brief discussions of the three primary areas where caution must be
observed.
Reflow Temperature Profile
The single most critical stage in the automated assembly process is the reflow
stage. The reflow profile below should not be exceeded, since excessive
temperatures or transport times during reflow will irreparably damage the
modules. Assembly personnel will need to pay careful attention to the oven’s
profile to ensure that it meets the requirements necessary to successfully reflow
all components while still remaining within the limits mandated by the modules.
The figure below shows the recommended reflow oven profile for the modules.
The modules are housed in a hybrid SMD package that supports hand or
automated assembly techniques. Since the modules contain discrete
components internally, the assembly procedures are critical to ensuring the
reliable function of the modules. The following procedures should be reviewed
with and practiced by all assembly personnel.
HAND ASSEMBLY
Pads located on the bottom of the
Soldering Iron
module are the primary mounting
surface. Since these pads are
Tip
inaccessible during mounting,
300
250
200
150
100
255°C
235°C
217°C
185°C
180°C
125°C
Recommended RoHS Profile
Max RoHS Profile
Recommended Non-RoHS Profile
castellations that run up the side of
the module have been provided to
facilitate solder wicking to the
Solder
50
module’s underside. This allows for
very quick hand soldering for
PCB Pads
Castellations
0
30
60
90
120
150
180
210
240
270
300
330
360
prototyping and small volume
Time ( S econd s )
production.
Figure 14: Soldering Technique
Figure 15: Maximum Reflow Profile
If the recommended pad guidelines have been followed, the pads will protrude
slightly past the edge of the module. Use a fine soldering tip to heat the board
pad and the castellation, then introduce solder to the pad at the module’s edge.
The solder will wick underneath the module, providing reliable attachment. Tack
one module corner first and then work around the device, taking care not to
exceed the times listed below.
Absolute Maximum Solder Times
Hand-Solder Temp. TX +225°C for 10 Seconds
Hand-Solder Temp. RX +225°C for 10 Seconds
Recommended Solder Melting Point +180°C
Reflow Oven: +220°C Max. (See adjoining diagram)
Page 12
Shock During Reflow Transport
Since some internal module components may reflow along with the components
placed on the board being assembled, it is imperative that the modules not be
subjected to shock or vibration during the time solder is liquid. Should a shock
be applied, some internal components could be lifted from their pads, causing
the module to not function properly.
Washability
The modules are wash resistant, but are not hermetically sealed. Linx
recommends wash-free manufacturing; however, the modules can be subjected
to a wash cycle provided that a drying time is allowed prior to applying electrical
power to the modules. The drying time should be sufficient to allow any moisture
that may have migrated into the module to evaporate, thus eliminating the
potential for shorting damage during power-up or testing. If the wash contains
contaminants, the performance may be adversely affected, even after drying.
Page 13
相关PDF资料 |
PDF描述 |
|---|---|
| TC25M6A32K7680 | OSCILLATOR 32.7680 KHZ 1.8V SMD |
| MODEL 19-230 | CURRENT TRANSFORMER .29" WINDOW |
| MDEV-433-HH-CP8-HS | KIT DEV TX 433MHZ HS COMPACT |
| EVAL-433-KF | KIT EVAL KEYFOB 433 MHZ 5 BUTTON |
| CR8401-1000 | TRANSFORMER CURRENT GENERAL PURP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-916-ES | 功能描述:射频开发工具 ES Basic Eval System 916MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| EVAL-916-SC-P | 功能描述:KIT BASIC EVAL 900MHZ SC SERIES RoHS:否 类别:RF/IF 和 RFID >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:用于 200/300 系列的欧盟开发套件 适用于相关产品:Zensys RF 模块 所含物品:开发板，模块，编程器，软件，线缆，电源 其它名称:703-1019Q3225667 |
| EVAL-916-SC-PA | 功能描述:KIT BASIC EVAL 900MHZ SC SERIES RoHS:否 类别:RF/IF 和 RFID >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:用于 200/300 系列的欧盟开发套件 适用于相关产品:Zensys RF 模块 所含物品:开发板，模块，编程器，软件，线缆，电源 其它名称:703-1019Q3225667 |
| EVALA5970AD | 功能描述:电源管理IC开发工具 POWER SUPPLY EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| EVALA5970D | 功能描述:电源管理IC开发工具 EVAL BOARD A5970D Auto Grade RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。