- 您现在的位置：买卖IC网 > PDF目录16581 > EVAL-AD5258DBZ (Analog Devices Inc)BOARD EVAL FOR AD5258DBZ PDF资料下载
参数资料
| 型号： | EVAL-AD5258DBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5258DBZ |
| 标准包装： | 1 |
| 系列： | * |
Data Sheet
AD5258
Rev. D | Page 19 of 24
ESD PROTECTION OF DIGITAL PINS AND
RESISTOR TERMINALS
The AD5258 VDD, VLOGIC, and GND power supplies define the
boundary conditions for proper 3-terminal and digital input
operation. Supply signals present on Terminal A, Terminal B,
and Terminal W that exceed VDD or GND are clamped by the
internal forward-biased ESD protection diodes (see Figure 40).
Digital Input SCL and Digital Input SDA are clamped by ESD
protection diodes with respect to VLOGIC and GND as shown in
GND
A
W
B
VDD
05029-
041
Figure 40. Maximum Terminal Voltages Set by VDD and GND
05029-
042
GND
SCL
SDA
VLOGIC
Figure 41. Maximum Terminal Voltages Set by VLOGIC and GND
POWER-UP SEQUENCE
Because the ESD protection diodes limit the voltage compliance
at Terminal A, Terminal B, and Terminal W (see Figure 40), it is
important to power GND/VDD/VLOGIC before applying any volt-
age to Terminal A, Terminal B, and Terminal W; otherwise, the
diode is forward-biased such that VDD and VLOGIC are powered
unintentionally and may affect the user’s circuit. The ideal
power-up sequence is in the following order: GND, VDD,
VLOGIC, digital inputs, and then VA, VB, VW. The relative order
of powering VA, VB, VW and the digital inputs is not important
as long as they are powered after GND, VDD, and VLOGIC.
LAYOUT AND POWER SUPPLY BYPASSING
It is good practice to employ compact, minimum lead length
layout design. The leads to the inputs should be as direct as
possible with minimum conductor length. Ground paths
should have low resistance and low inductance.
Similarly, it is also good practice to bypass the power supplies
with quality capacitors for optimum stability. Supply leads to
the device should be bypassed with disc or chip ceramic capaci-
tors of 0.01 F to 0.1 F. In addition, low ESR 1 F to 10 F
tantalum or electrolytic capacitors should be applied at the
supplies to minimize any transient disturbance and low fre-
quency ripple (see Figure 42). As well, the digital ground
should be joined remotely to the analog ground at one point
to minimize the ground bounce.
VDD
GND
VDD
C2
10F
C1
0.1F
AD5258
+
05029-
043
Figure 42. Power Supply Bypassing
MULTIPLE DEVICES ON ONE BUS
The AD5258 has two configurable address pins, AD0 and AD1.
The state of these two pins is registered upon power-up and
decoded into a corresponding I2C-compatible 7-bit address (see
Table 5). This allows up to four devices on the bus to be written
to or read from independently.
相关PDF资料 |
PDF描述 |
|---|---|
| SRR1240-4R7M | INDUCTOR POWER 4.7UH 6A SMD |
| EET-UQ2W151CA | CAP ALUM 150UF 450V 20% SNAP |
| GCM18DRYH-S13 | CONN EDGECARD 36POS .156 EXTEND |
| EVAL-AD5247DBZ | BOARD EVAL FOR AD5247DBZ |
| EEM43DSEN-S13 | CONN EDGECARD 86POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5259DBZ | 功能描述:BOARD EVAL FOR AD5259DBZ RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5262EBZ | 功能描述:BOARD EVAL FOR AD5262 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5263EBZ | 功能描述:BOARD EVAL AD5263 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5270SDZ | 功能描述:BOARD EVAL FOR AD5270 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5272SDZ | 功能描述:BOARD EVAL FOR AD5272 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
发布紧急采购，3分钟左右您将得到回复。