- 您现在的位置：买卖IC网 > PDF目录16581 > EVAL-AD5259DBZ (Analog Devices Inc)BOARD EVAL FOR AD5259DBZ PDF资料下载
参数资料
| 型号： | EVAL-AD5259DBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5259DBZ |
| 标准包装： | 1 |
| 系列： | * |
Data Sheet
AD5259
Rev. C | Page 15 of 24
I2C-COMPATIBLE INTERFACE
The master initiates data transfer by establishing a start condi-
tion, which is when a high-to-low transition on the SDA line
occurs while SCL is high (see Figure 4). The next byte is the
slave address byte, which consists of the slave address (first
7 bits) followed by an R/W bit (see Table 6). When the R/W bit
is high, the master reads from the slave device. When the R/W
bit is low, the master writes to the slave device.
The slave address of the part is determined by two configurable
address pins, Pin AD0 and Pin AD1. The state of these two pins
is registered upon power-up and decoded into a corresponding
to the transmitted address bits responds by pulling the SDA
line low during the ninth clock pulse (this is termed the slave
acknowledge bit). At this stage, all other devices on the bus
remain idle while the selected device waits for data to be
written to, or read from, its serial register.
WRITING
In the write mode, the last bit (R/W) of the slave address byte is
logic low. The second byte is the instruction byte. The first three
bits of the instruction byte are the command bits (see Table 6).
The user must choose whether to write to the RDAC register,
EEPROM register, or activate the software write protect (see
Table 7 to Table 10). The final five bits are all zeros (see Table 13
to Table 14). The slave again responds by pulling the SDA line
low during the ninth clock pulse.
The final byte is the data byte MSB first. With the write protect
mode, data is not stored; rather, a logic high in the LSB enables
write protect. Likewise, a logic low disables write protect. The
slave again responds by pulling the SDA line low during the
ninth clock pulse.
STORING/RESTORING
In this mode, only the address and instruction bytes are
necessary. The last bit (R/W) of the address byte is logic
low. The first three bits of the instruction byte are the
command bits (see Table 6). The two choices are transfer
data from RDAC to EEPROM (store), or from EEPROM
to RDAC (restore). The final five bits are all zeros (see
Table 13 to Table 14). In addition, users should issue an
NOP command immediately after restoring the EEMEM
setting to RDAC, thereby minimizing supply current
dissipation.
READING
Assuming the register of interest was not just written to, it is
necessary to write a dummy address and instruction byte. The
instruction byte will vary depending on whether the data that
is wanted is the RDAC register, EEPROM register, or tolerance
register (see Table 11 and Table 16).
After the dummy address and instruction bytes are sent, a repeat
start is necessary. After the repeat start, another address byte is
needed, except this time the R/W bit is logic high. Following this
address byte is the readback byte containing the information
requested in the instruction byte. Read bits appear on the nega-
tive edges of the clock.
The tolerance register can be read back individually (see
Modes section for detailed information on the interpretation
of the tolerance bytes.
After all data bits have been read or written, a stop condition is
established by the master. A stop condition is defined as a low-to-
high transition on the SDA line while SCL is high. In write mode,
the master pulls the SDA line high during the tenth clock pulse
to establish a stop condition (see Figure 46). In read mode, the
master issues a no acknowledge for the ninth clock pulse (that is,
the SDA line remains high). The master then brings the SDA line
low before the tenth clock pulse, and then raises SDA high to
establish a stop condition (see Figure 47).
A repeated write function gives the user flexibility to update the
RDAC output a number of times after addressing and instructing
the part only once. For example, after the RDAC has acknowl-
edged its slave address and instruction bytes in the write mode,
the RDAC output is updated on each successive byte until a stop
condition is received. If different instructions are needed, the
write/read mode has to start again with a new slave address,
instruction, and data byte. Similarly, a repeated read function
of the RDAC is also allowed.
相关PDF资料 |
PDF描述 |
|---|---|
| GCM18DRYN-S13 | CONN EDGECARD 36POS .156 EXTEND |
| EET-UQ2E471JA | CAP ALUM 470UF 250V 20% SNAP |
| EVAL-AD5258DBZ | BOARD EVAL FOR AD5258DBZ |
| SRR1240-4R7M | INDUCTOR POWER 4.7UH 6A SMD |
| EET-UQ2W151CA | CAP ALUM 150UF 450V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD5262EBZ | 功能描述:BOARD EVAL FOR AD5262 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5263EBZ | 功能描述:BOARD EVAL AD5263 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5270SDZ | 功能描述:BOARD EVAL FOR AD5270 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5272SDZ | 功能描述:BOARD EVAL FOR AD5272 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-AD5273DBZ | 功能描述:BOARD EVAL FOR AD5273DBZ RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
发布紧急采购，3分钟左右您将得到回复。