- 您现在的位置：买卖IC网 > PDF目录17038 > EVAL-AD7651CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7651 PDF资料下载
参数资料
| 型号： | EVAL-AD7651CBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD7651 |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 100k |
| 数据接口： | 串行，并联 |
| 输入范围： | 0 ~ 2.5 V |
| 在以下条件下的电源（标准）： | 16mW @ 100kSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7651 |
| 已供物品： | 板 |
| 相关产品： | AD7651ASTZ-ND - IC ADC 16BIT 100KSPS 48-LQFP AD7651ACPZ-ND - IC ADC 16BIT UNIPOLAR 48LFCSP AD7651ASTZRL-ND - IC ADC 16BIT UNIPOLAR 48LFCSP AD7651ACPZRL-ND - IC ADC 16BIT UNIPOLAR 48LQFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD7651
APPLICATION HINTS
BIPOLAR AND WIDER INPUT RANGES
In some applications, it is desirable to use a bipolar or wider
analog input range such as ±10 V, ±5 V, or 0 V to 5 V. Although
the AD7651 has only one unipolar range, simple modifications
of input driver circuitry allow bipolar and wider input ranges to
be used without any performance degradation.
shows
a connection diagram that allows this. Component values
required and resulting full-scale ranges are shown in
Figure 38. Using the AD7651 in 16-Bit Bipolar and/or Wider Input Ranges
Table 8. Component Values and Input Ranges
When desired, accurate gain and offset can be calibrated by
acquiring a ground and voltage reference using an analog
multiplexer (U2), as shown in
U1
ANALOG
INPUT
R2
R3
R4
100nF
R1
U2
CREF
IN
INGND
REF
REFGND
AD7651
02964-0-022
CF
Input Range
R1 ()
R2 (k)
R3 (k)
R4 (k)
±10 V
500
4
2.5
2
±5 V
500
2
2.5
1.67
0 V to –5 V
500
1
None
0
LAYOUT
The AD7651 has very good immunity to noise on the power
supplies. However, care should still be taken with regard to
grounding layout.
The printed circuit board that houses the AD7651 should be
designed so the analog and digital sections are separated and
confined to certain areas of the board. This facilitates the use of
ground planes that can be separated easily. Digital and analog
ground planes should be joined in only one place, preferably
underneath the AD7651, or as close as possible to the AD7651.
If the AD7651 is in a system where multiple devices require
analog-to-digital ground connections, the connection should
still be made at one point only, a star ground point that should
be established as close as possible to the AD7651.
Running digital lines under the device should be avoided since
these will couple noise onto the die. The analog ground plane
should be allowed to run under the AD7651 to avoid noise
coupling. Fast switching signals like CNVST or clocks should be
shielded with digital ground to avoid radiating noise to other
sections of the board, and should never run near analog signal
paths. Crossover of digital and analog signals should be avoided.
Traces on different but close layers of the board should run at
right angles to each other. This will reduce the effect of crosstalk
through the board.
The power supply lines to the AD7651 should use as large a
trace as possible to provide low impedance paths and reduce the
effect of glitches on the power supply lines. Good decoupling is
also important to lower the supply’s impedance presented to the
AD7651 and to reduce the magnitude of the supply spikes.
Decoupling ceramic capacitors, typically 100 nF, should be
placed on each power supply pin—AVDD, DVDD, and
OVDD—close to, and ideally right up against these pins and
their corresponding ground pins. Additionally, low ESR 10 F
capacitors should be located near the ADC to further reduce
low frequency ripple.
The DVDD supply of the AD7651 can be a separate supply or
can come from the analog supply AVDD or the digital interface
supply OVDD. When the system digital supply is noisy or when
fast switching digital signals are present, if no separate supply is
available, the user should connect DVDD to AVDD through an
RC filter (see F
) and the system supply to OVDD and
the remaining digital circuitry. When DVDD is powered from
the system supply, it is useful to insert a bead to further reduce
high frequency spikes.
The AD7651 has five different ground pins: INGND, REFGND,
AGND, DGND, and OGND. INGND is used to sense the analog
input signal. REFGND senses the reference voltage and, because
it carries pulsed currents, should be a low impedance return to
the reference. AGND is the ground to which most internal ADC
analog signals are referenced; it must be connected with the
least resistance to the analog ground plane. DGND must be tied
to the analog or digital ground plane depending on the
configuration. OGND is connected to the digital system
ground.
EVALUATING THE AD7651’S PERFORMANCE
A recommended layout for the AD7651 is outlined in the
EVAL-AD7651 evaluation board for the AD7651. The
evaluation board package includes a fully assembled and tested
evaluation board, documentation, and software for controlling
the board from a PC via the EVAL-CONTROL BRD2.
Rev. 0 | Page 25 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| EVAL-AD7694CBZ | BOARD EVALUATION FOR AD7694 |
| 0210490994 | CABLE JUMPER 1.25MM .127M 29POS |
| RBC08DREH-S93 | CONN EDGECARD 16POS .100 EYELET |
| EVAL-AD7684CBZ | BOARD EVALUATION FOR AD7684 |
| HBC06DRTN-S93 | CONN EDGECARD 12POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7651EDZ | 功能描述:BOARD EVAL FOR AD7651 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7652CB | 制造商:Analog Devices 功能描述:DEV TOOLS, 16BIT 500KSPS SAR UNIPOLAR ADC W/ REF - Bulk |
| EVAL-AD7652CBZ | 功能描述:BOARD EVALUATION FOR AD7652 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7652EDZ | 功能描述:BOARD EVAL FOR AD7652 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7653CB | 制造商:Analog Devices 功能描述:Development Tools, 16Bit 1MSPS SAR Unipolar ADC with Ref 制造商:Analog Devices 功能描述:DEV TOOLS, 16BIT 1MSPS SAR UNIPOLAR ADC W/ REF - Bulk |
发布紧急采购，3分钟左右您将得到回复。