参数资料
型号: EVAL-AD7985EBZ
厂商: Analog Devices Inc
文件页数: 15/28页
文件大小: 0K
描述: BOARD EVAL FOR AD7985
标准包装: 1
系列: PulSAR®
ADC 的数量: 1
位数: 16
采样率(每秒): 2.5M
数据接口: SPI?、QSPI?、MICROWIRE? 和 DSP
输入范围: 0 ~ 5 V
在以下条件下的电源(标准): 15.5mW @ 2.5MSPS
工作温度: -40°C ~ 85°C
已用 IC / 零件: AD7985
已供物品:
AD7985
Rev. A | Page 22 of 28
CS MODE, 4-WIRE WITH BUSY INDICATOR
This mode is usually used when a single AD7985 is connected
to an SPI-compatible digital host with an interrupt input and
when it is desired to keep CNV, which is used to sample the
analog input, independent of the signal used to select the data
reading. This independence is particularly important in applica-
tions where low jitter on CNV is desired. This mode is available
only in normal conversion mode (TURBO is low). The connection
diagram is shown in Figure 32, and the corresponding timing is
With SDI high, a rising edge on CNV initiates a conversion,
selects CS mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback. (If SDI and CNV are low, SDO is
driven low.) Prior to the minimum conversion time, SDI can be
used to select other SPI devices, such as analog multiplexers, but
SDI must be returned low before the minimum conversion time
elapses and then held low for the maximum possible conversion
time to guarantee the generation of the busy signal indicator.
When the conversion is complete, SDO goes from high imped-
ance to low impedance. With a pull-up on the SDO line, this
transition can be used as an interrupt signal to initiate the data
readback controlled by the digital host. The AD7985 then enters
the acquisition phase and powers down. The data bits are then
clocked out, MSB first, by subsequent SCK falling edges. The
data is valid on both SCK edges. Although the rising edge can
be used to capture the data, a digital host using the SCK falling
edge allows a faster reading rate, provided that it has an accept-
able hold time. After the optional 17th SCK falling edge or when
SDI goes high (whichever occurs first), SDO returns to high
impedance.
AD7985
SDI
SDO
CNV
SCK
CONVERT
DATA IN
CLK
DIGITAL HOST
IRQ
VIO
47k
CS1
TURBO
07947-
015
Figure 32. CS Mode, 4-Wire with Busy Indicator Connection Diagram
(I/O QUIET
TIME)
SDO
D15
D14
D1
D0
tDIS
tQUIET
SCK
1
2
3
15
16
17
tSCK
tSCKL
tSCKH
tHSDO
tDSDO
tEN
CONVERSION
ACQUISITION
tCONV
tCYC
tACQ
ACQUISITION
SDI
CNV
tSSDICNV
tHSDICNV
TURBO = 0
07947-
016
Figure 33. CS Mode, 4-Wire with Busy Indicator Serial Interface Timing
相关PDF资料
PDF描述
RPP20-2412D/N CONV DC/DC 20W 18-36VIN +/-12V
EBA22DTKH-S288 CONN EDGECARD 44POS .125 EXTEND
0982660123 CBL 12POS 0.5MM JMPR TYPE A 4"
RPP20-2405S/N CONV DC/DC 20W 18-36VIN 05VOUT
EBM28DCTN CONN EDGECARD 56POS DIP .156 SLD
相关代理商/技术参数
参数描述
EVAL-AD7986EBZ 功能描述:BOARD EVAL FOR AD7986 RoHS:是 类别:编程器,开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率(每秒):94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源(标准):- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,软件
EVAL-AD7988-5SDZ 功能描述:BAORD EVAL FOR AD7988-5 RoHS:是 类别:编程器,开发系统 >> 评估板 - 模数转换器 (ADC) 系列:PulSAR® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率(每秒):94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源(标准):- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,软件
EVAL-AD7991EBZ 功能描述:BOARD EVAL FOR AD7991 RoHS:是 类别:编程器,开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率(每秒):94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源(标准):- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,软件
EVAL-AD7991EBZ 制造商:Analog Devices 功能描述:AD7991, ADC, I2C, EVALUATION BOARD
EVAL-AD7992CB 制造商:AD 制造商全称:Analog Devices 功能描述:2-Channel, 12-Bit ADC with I2C-Compatible