参数资料
| 型号： | EVAL-ADE7762EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR ADE7762 |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电度表/功率表 |
| 已用 IC / 零件： | ADE7762 |
| 已供物品： | 板 |
| 相关产品： | ADE7762ARWZ-ND - IC ENERGY METERING 3PHASE 28SOIC ADE7762ARWZ-RL-ND - IC ENERGY METERING 3PHASE 28SOIC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ADE7762
PHASE MONITOR
The ADE7762 has phase monitoring functions to detect phase
dropout, phase sequence error, and reverse polarity using four
pins. Phase dropout has the highest priority, and reverse
polarity has the lowest priority. If a phase dropout occurs, phase
sequence error indication is disabled until all three phases are
section). Because the dropout detection level is not set to zero, a
phase can have some small voltage during a phase dropout
condition. Therefore, reverse polarity is still indicated on that
phase if the proper conditions occur.
The phase monitor circuit functions by multiplexing signals onto
the four pins. The four multiplexed pins are LED_CTRL, LED_A,
LED_B, and LED_C. Two LEDs can be connected to each pin as
shown in Figure 21. When LED_CTRL is high, LED_A is low to
turn on an LED and indicate a phase drop condition on Phase A.
When LED_CTRL is low, LED_A is high to indicate a reverse
polarity (REVP) condition on Phase A. Phase sequence error is
indicated by blinking the Phase Seq/Drop LEDs.
LED_CTRL switches at a rate of 131 kHz so that both the Phase
Seq/Drop LEDs and REVP LEDs can appear to be on simultane-
ously, which allows indication of phase dropout and REVP at the
LED_CTRL
PHASE
SEQ/DROP
PHASE DROPOUT ERROR
The ADE7762 indicates a phase drop condition when there is a
low voltage signal or no voltage signal on a phase. The phase
dropout condition occurs when the amplitude of the phase
drops below 20% of full-scale analog input voltage or when a
zero crossing is not followed by another zero crossing on that
phase for 150 ms. When this occurs, a phase dropout signal is
generated, and the Phase Seq/Drop LED is turned on for the
missing phase. The delay between the phase drop condition
occurring at the analog inputs and indication of the condition
on the LED outputs is approximately 150 ms. During a phase
dropout condition, energy continues to accumulate on the
dropped channel, as well as the other channels, and phase
sequence error indication is disabled. The Phase Seq/Drop LED
for the dropped phase is turned off when the zero crossings
return for more than 150 ms and there is more than 20% of full-
scale input voltage on the voltage input of that phase.
PHASE SEQUENCE ERROR
The ADE7762 detects the zero crossing of each phase. A phase
sequence error occurs when the sequence A>B>C>A> … is
violated. If a phase sequence error occurs, the Phase Seq/Drop
LEDs blink at 1 Hz (see Figure 22).
Phase sequence error and REVP can be displayed simultane-
PHASE
SEQ/DROP
PHASE
SEQ/DROP
REVP
R LOAD
REVP
R LOAD
LED_A
LED_B
ously. The REVP LEDs continue to indicate reverse polarity if
the proper conditions exist. For example, if the phase sequence
becomes A>C>B>A… and Phase B has negative active energy
accumulated, then the REVP LED for Phase B is on solid, and
all of the Phase Seq/Drop LEDs are blinking at 1 Hz. The delay
REVP
R LOAD
Figure 21. Phase Monitor Circuit
LED_C
in indicating the phase sequence error with blinking LEDs is
approximately 150 ms from the time that a phase sequence
error occurs.
PHASE REVERSE POLARITY DETECTION
When reverse power is detected on any phase, the correspond-
ing REVP LED turns on for that phase. For example, if the
power for Phase A is negative, the REVP LED connected to
LED_A turns on. The indication of REVP on the LED_A,
LED_B, or LED_C pins is nearly instantaneous. As soon as the
input to the ADCs changes and the power is calculated such
that there is a reverse power condition on any phase, the
appropriate LED is turned on.
Rev. 0 | Page 18 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| EVAL-ADE7763ZEB | BOARD EVALUATION FOR ADE7763 |
| EVAL-ADE7816EBZ | BOARD EVALUATION FOR ADE7816 |
| EVAL-ADE7878EBZ | BOARD EVAL FOR ADE7878 |
| EVAL-ADE7880EBZ | BOARD EVAL FOR ADE7880 |
| EVAL-ADE7953EBZ | BOARD EVAL FOR ADE7953 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADE7763EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD DOCUMENTATION ADE7763 ENERGY METERING IC |
| EVAL-ADE7763ZEB | 功能描述:BOARD EVALUATION FOR ADE7763 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| EVAL-ADE7816EBZ | 功能描述:BOARD EVALUATION FOR ADE7816 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| EVAL-ADE7854EBZ | 制造商:Analog Devices 功能描述:EVALUATION BOARDS - Boxed Product (Development Kits) |
| EVAL-ADE7858EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Poly Phase Multifunction Energy Metering IC with per Phase Active and Reactive Powers |
发布紧急采购，3分钟左右您将得到回复。