- 您现在的位置：买卖IC网 > PDF目录16679 > EVAL-ADM2682EEBZ (Analog Devices Inc)BOARD EVAL ADM2682 PDF资料下载
参数资料
| 型号： | EVAL-ADM2682EEBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL ADM2682 |
| 视频文件： | ADM2682E / ADM2687E 5kVrms Signal & Power Isolated RS-485 Transceivers |
| 标准包装： | 1 |
| 主要目的： | 接口，收发器，RS-422/RS-485 |
| 已用 IC / 零件： | ADM2682 |
| 已供物品： | 板 |
ADM2682E/ADM2687E
CIRCUIT DESCRIPTION
SIGNAL ISOLATION
Data Sheet
Table 13. Receiving (see Table 11 for Abbreviations)
The ADM2682E / ADM2687E signal isolation of 5 kV rms is
implemented on the logic side of the interface. The part achieves
A?B
Inputs
RE
Output
RxD
signal isolation by having a digital isolation section and a trans-
ceiver section (see Figure 1). Data applied to the TxD and DE
pins and referenced to logic ground (GND 1 ) are coupled across
an isolation barrier to appear at the transceiver section referenced
to isolated ground (GND 2 ). Similarly, the single-ended receiver
≥ ?0.03 V
≤ ?0.2 V
?0.2 V < A ? B < ?0.03 V
Inputs open
X
L or NC
L or NC
L or NC
L or NC
H
H
L
I
H
Z
output signal, referenced to isolated ground in the transceiver
section, is coupled across the isolation barrier to appear at the
RxD pin referenced to logic ground.
POWER ISOLATION
The ADM2682E / ADM2687E power isolation of 5 kV rms is
implemented using an iso Power integrated isolated dc-to-dc
ADM2687E works on principles that are common to most
modern power supplies. It is a secondary side controller
architecture with isolated pulse-width modulation (PWM)
feedback. V CC power is supplied to an oscillating circuit that
switches current into a chip-scale air core transformer. Power
transferred to the secondary side is rectified and regulated to
3.3 V. The secondary (V ISO ) side controller regulates the output
by creating a PWM control signal that is sent to the primary
(V CC ) side by a dedicated i Coupler (5 kV rms signal isolated)
data channel. The PWM modulates the oscillator circuit to
control the power being sent to the secondary side. Feedback
allows for significantly higher power and efficiency.
TRUTH TABLES
The truth tables in this section use the abbreviations found in
Table 11. Truth Table Abbreviations
Letter Description
H High level
THERMAL SHUTDOWN
The ADM2682E / ADM2687E contain thermal shutdown circuitry
that protects the parts from excessive power dissipation during
fault conditions. Shorting the driver outputs to a low impedance
source can result in high driver currents. The thermal sensing
circuitry detects the increase in die temperature under this
condition and disables the driver outputs. This circuitry is
designed to disable the driver outputs when a die temperature
of 150°C is reached. As the device cools, the drivers are reenabled
at a temperature of 140°C.
OPEN- AND SHORT-CIRCUIT, FAIL-SAFE RECEIVER
INPUTS
The receiver inputs have open- and short-circuit, fail-safe features
that ensure that the receiver output is high when the inputs are
open or shorted. During line-idle conditions, when no driver on
the bus is enabled, the voltage across a terminating resistance at
the receiver input decays to 0 V. With traditional transceivers,
receiver input thresholds specified between ?200 mV and
+200 mV mean that external bias resistors are required on the
A and B pins to ensure that the receiver outputs are in a known
state. The short-circuit, fail-safe receiver input feature eliminates
the need for bias resistors by specifying the receiver input threshold
between ?30 mV and ?200 mV. The guaranteed negative threshold
means that when the voltage between A and B decays to 0 V, the
receiver output is guaranteed to be high.
L
X
I
Z
NC
Low level
Don’t care
Indeterminate
High impedance (off )
Disconnected
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
The digital signals transmit across the isolation barrier using
i Coupler technology. This technique uses chip-scale transformer
windings to couple the digital signals magnetically from one
side of the barrier to the other. Digital inputs are encoded into
waveforms that are capable of exciting the primary transformer
Table 12. Transmitting (see Tabl e 11 for Abbreviations)
Inputs Outputs
DE TxD Y Z
H H H L
H L L H
L X Z Z
X X Z Z
winding. At the secondary winding, the induced waveforms are
decoded into the binary value that was originally transmitted.
Positive and negative logic transitions at the isolator input cause
narrow (~1 ns) pulses to be sent to the decoder via the transformer.
The decoder is bistable and is, therefore, either set or reset by
the pulses, indicating input logic transitions. In the absence of
logic transitions at the input for more than 1 μs, periodic sets of
refresh pulses indicative of the correct input state are sent to
ensure dc correctness at the output. If the decoder receives no
internal pulses of more than approximately 5 μs, the input side
Rev. B | Page 16 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| EEV-FC1C680P | CAP ALUM 68UF 16V 20% SMD |
| 0982660343 | CBL 32POS 0.5MM JMPR TYPE A 4" |
| H2F1.38BK | 2:1 FAB HEATSHRINK BLK 35MM 100' |
| H3DKH-1018G | IDC CABLE - HKR10H/AE10G/HPK10H |
| EVAL-ADM3053EBZ | BOARD EVAL FOR ADM3053EBZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADM2687EEBZ | 功能描述:BOARD EVAL ADM2687 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| EVAL-ADM2914EBZ | 功能描述:BOARD EVAL FOR ADM2914 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-ADM3051EBZ | 功能描述:EVAL BOARD FOR ADM3051 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| EVAL-ADM3052EBZ | 功能描述:BOARD EVAL FOR ADM3052EBZ RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:iCoupler® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| EVAL-ADM3053EBZ | 功能描述:BOARD EVAL FOR ADM3053EBZ RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:IsoPower®, iCoupler® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
发布紧急采购，3分钟左右您将得到回复。