- 您现在的位置：买卖IC网 > PDF目录16679 > EVAL-ADM3053EBZ (Analog Devices Inc)BOARD EVAL FOR ADM3053EBZ PDF资料下载
参数资料
| 型号： | EVAL-ADM3053EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADM3053EBZ |
| 标准包装： | 1 |
| 系列： | IsoPower®, iCoupler® |
| 主要目的： | 接口，CAN |
| 已用 IC / 零件： | ADM3053 |
| 已供物品： | 板 |
Data Sheet
ADM3053
Rev. B | Page 15 of 20
APPLICATIONS INFORMATION
PCB LAYOUT
The ADM3053 signal and power isolated CAN transceiver
contains an isoPower integrated dc-to-dc converter, requiring
no external interface circuitry for the logic interfaces. Power
supply bypassing is required at the input and output supply pins
(see Figure 28). The power supply section of the ADM3053 uses
a 180 MHz oscillator frequency to pass power efficiently through
its chip-scale transformers. In addition, the normal operation of
the data section of the iCoupler introduces switching transients
on the power supply pins.
Bypass capacitors are required for several operating frequencies.
Noise suppression requires a low inductance, high frequency
capacitor, whereas ripple suppression and proper regulation
require a large value capacitor. These capacitors are connected
between GND1 and Pin 6 (VIO) for VIO. It is recommended that
a combination of 100 nF and 10 nF be placed as shown in Figure
28 (C6 and C4). It is recommended that a combination of two
capacitors, with values of 100 nF and 10 μF, are placed between
and C1). The VISOIN and VISOOUT capacitors are connected between
Pin 11 (GND2) and Pin 12 (VISOOUT) with recommended values
of 100 nF and 10 μF as shown in Figure 28 (C5 and C8). Two
capacitors are recommended to be fitted Pin 19 (VISOIN) and Pin 20
(GND2) with values of 100nF and 10nF as shown in Figure 28
(C9 and C7). The best practice recommended is to use a very low
inductance ceramic capacitor, or its equivalent, for the smaller
value. The total lead length between both ends of the capacitor
and the input power supply pin should not exceed 10 mm.
0929
3-
012
Figure 28. Recommended PCB Layout
In applications involving high common-mode transients, ensure
that board coupling across the isolation barrier is minimized.
Furthermore, design the board layout such that any coupling
that does occur equally affects all pins on a given component
side. Failure to ensure this can cause voltage differentials between
pins exceeding the absolute maximum ratings for the device,
thereby leading to latch-up and/or permanent damage.
The ADM3053 dissipates approximately 650 mW of power
when fully loaded. Because it is not possible to apply a heat sink
to an isolation device, the devices primarily depend on heat
dissipation into the PCB through the GND pins. If the devices
are used at high ambient temperatures, provide a thermal path
from the GND pins to the PCB ground plane. The board layout
in Figure 28 shows enlarged pads for Pin 1, Pin 3, Pin 9, Pin 10,
Pin 11, Pin 14, Pin 16, and Pin 20. Implement multiple vias from
the pad to the ground plane to reduce the temperature inside the
chip significantly. The dimensions of the expanded pads are at
the discretion of the designer and dependent on the available
board space.
EMI CONSIDERATIONS
The dc-to-dc converter section of the ADM3053 must, of
necessity, operate at very high frequency to allow efficient
power transfer through the small transformers. This creates
high frequency currents that can propagate in circuit board
ground and power planes, causing edge and dipole radiation.
Grounded enclosures are recommended for applications that
use these devices. If grounded enclosures are not possible, good
RF design practices should be followed in the layout of the PCB.
See the AN-0971 Application Note, Control of Radiated Emissions
with isoPower Devices, for more information.
INSULATION LIFETIME
All insulation structures eventually break down when subjected to
voltage stress over a sufficiently long period. The rate of insulation
degradation is dependent on the characteristics of the voltage
waveform applied across the insulation. Analog Devices conducts
an extensive set of evaluations to determine the lifetime of the
insulation structure within the ADM3053.
Accelerated life testing is performed using voltage levels higher
than the rated continuous working voltage. Acceleration factors for
several operating conditions are determined, allowing calculation
of the time to failure at the working voltage of interest. The values
shown in Table 5 summarize the peak voltages for 50 years of
service life in several operating conditions. In many cases, the
working voltage approved by agency testing is higher than the 50
year service life voltage. Operation at working voltages higher than
the service life voltage listed leads to premature insulation
failure.
The insulation lifetime of the ADM3053 depends on the voltage
waveform type imposed across the isolation barrier. The iCoupler
insulation structure degrades at different rates, depending on
whether the waveform is bipolar ac, unipolar ac, or dc. Figure 29,
Figure 30, and Figure 31 illustrate these different isolation voltage
waveforms.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B1H-EW | CONVERTER MOD DC/DC 52V 100W |
| ZXRE4041ERSTOB | IC VREF SHUNT PREC 1.225V TO92-3 |
| H2F1.18BK | 2:1 FAB HEATSHRINK BLK 30MM 100' |
| EBM24DRKF-S13 | CONN EDGECARD 48POS .156 EXTEND |
| H1BXH-2636G | IDC CABLE - HSR26H/AE26G/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADM3054EBZ | 功能描述:EVAL BOARD FOR ADM3054 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| EVAL-ADM3251EEB1Z | 功能描述:BOARD EVALUATION FOR ADM3251 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:isoPower® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| EVAL-ADM3251EEBZ | 功能描述:BOARD EVALUATION ADM3251 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:isoPower® 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
| EVAL-ADM3252EEBZ | 功能描述:BOARD EVAL FOR ADM3252E RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| EVAL-ADM4168EEBZ | 功能描述:界面开发工具 EVALUATION BOARD RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。