参数资料
| 型号： | EX256-FTQ100 |
| 厂商： | Microsemi SoC |
| 文件页数： | 9/48页 |
| 文件大小： | 0K |
| 描述： | IC FPGA ANTIFUSE 12K 100-TQFP |
| 标准包装： | 90 |
| 系列： | EX |
| 逻辑元件/单元数： | 512 |
| 输入/输出数： | 81 |
| 门数： | 12000 |
| 电源电压： | 2.3 V ~ 2.7 V |
| 安装类型： | 表面贴装 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-TQFP（14x14） |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
eX Family FPGAs
Revision 10
1-13
Design Considerations
The TDI, TCK, TDO, PRA, and PRB pins should not be used as input or bidirectional ports. Since these
pins are active during probing, critical signals input through these pins are not available while probing. In
addition, the Security Fuse should not be programmed because doing so disables the probe circuitry. It is
recommended to use a series 70
termination resistor on every probe connector (TDI, TCK, TMS, TDO,
PRA, PRB). The 70
series termination is used to prevent data transmission corruption during probing
and reading back the checksum.
Development Tool Support
The eX family of FPGAs is fully supported by both Libero Integrated Design Environment and Designer
FPGA Development software. Libero IDE is a design management environment that streamlines the
design flow. Libero IDE provides an integrated design manager that seamlessly integrates design tools
while guiding the user through the design flow, managing all design and log files, and passing necessary
design data among tools. Additionally, Libero IDE allows users to integrate both schematic and HDL
synthesis into a single flow and verify the entire design in a single environment. Libero IDE includes
Synplify for Microsemi from Synplicity, ViewDraw for Microsemi from Mentor Graphics, ModelSim
HDL Simulator from Mentor Graphics, WaveFormer Lite from SynaptiCAD, and Designer software
from Microsemi. Refer to the Libero IDE flow (located on Microsemi SoC Product Group’s website)
diagram for more information.
Table 1-8 Device Configuration Options for Probe Capability (TRST pin reserved)
JTAG Mode
TRST1
Security Fuse
Programmed
PRA, PRB2
TDI, TCK, TDO2
Dedicated
LOW
No
User I/O3
Probing Unavailable
Flexible
LOW
No
User I/O3
Dedicated
HIGH
No
Probe Circuit Outputs
Probe Circuit Inputs
Flexible
HIGH
No
Probe Circuit Outputs
Probe Circuit Inputs
–
Yes
Probe Circuit Secured
Notes:
1. If TRST pin is not reserved, the device behaves according to TRST = HIGH in the table.
2. Avoid using the TDI, TCK, TDO, PRA, and PRB pins as input or bidirectional ports. Since these pins are active during
probing, input signals will not pass through these pins and may cause contention.
3. If no user signal is assigned to these pins, they will behave as unused I/Os in this mode. Unused pins are automatically
tristated by Microsemi Designer software.
Figure 1-13 Silicon Explorer II Probe Setup
Serial
Connection
Additional 16 Channels
(Logic Analyzer)
Silicon Explorer II
TDI
TCK
TMS
16 Pin
Connection
22 Pin
Connection
PRA
PRB
TDO
eX FPGAs
相关PDF资料 |
PDF描述 |
|---|---|
| EP4CE10E22C8LN | IC CYCLONE IV FPGA 10K 144EQFP |
| BR93L86FJ-WE2 | IC EEPROM 16KBIT 2MHZ 8SOP |
| EP4CE10E22C7N | IC CYCLONE IV FPGA 10K 144EQFP |
| AGL250V5-CS196I | IC FPGA 1KB FLASH 250K 196-CSP |
| AGL250V5-CSG196I | IC FPGA 1KB FLASH 250K 196-CSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EX256-FTQ100A | 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:eX Family FPGAs |
| EX256-FTQ100I | 制造商:未知厂家 制造商全称:未知厂家 功能描述:eX Family FPGAs |
| EX256-FTQ100PP | 制造商:未知厂家 制造商全称:未知厂家 功能描述:eX Family FPGAs |
| EX256-FTQ128 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:eX Family FPGAs |
| EX256-FTQ128I | 制造商:未知厂家 制造商全称:未知厂家 功能描述:eX Family FPGAs |
发布紧急采购，3分钟左右您将得到回复。