- 您现在的位置：买卖IC网 > PDF目录299041 > FAN2504S25 CCD Imaging ICs; Target Application: POS Barcode Scanner; Number of Pixels x Lines: 3648x1; Pixel Size (Micron): 8um x 200um; Resolution (dpi): 400; Data Rate (Color/BW) (MHz): 2; Sensitivity (G; BW) (V/lx.s): 160; Note: Elec.shutter PDF资料下载
参数资料
| 型号： | FAN2504S25 |
| 英文描述： | CCD Imaging ICs; Target Application: POS Barcode Scanner; Number of Pixels x Lines: 3648x1; Pixel Size (Micron): 8um x 200um; Resolution (dpi): 400; Data Rate (Color/BW) (MHz): 2; Sensitivity (G; BW) (V/lx.s): 160; Note: Elec.shutter |
| 中文描述： | 电压调节器|定额| 2.5V的|的CMOS |的TSOP | 6针|塑料 |
| 文件页数： | 4/10页 |
| 文件大小： | 547K |
| 代理商： | FAN2504S25 |
FAN2502/FAN2503
PRODUCT SPECIFICATION
REV. 1.1.6 2/11/02
3
Depending on the model selected, a number of control and
status functions are available to enhance the operation of the
LDO regulator. An Enable pin, available on all devices,
allows the user to shut down the regulator output to conserve
power, reducing supply current to less than 1A. The
adjustable-voltage versions of the device utilize pin 4 to
connect to an external voltage divider which feeds back to
the regulator error amplier, thereby setting the voltage as
desired. Two other functions are available at pin 4 in the
xed-voltage versions: in noise-sensitive applications, an
external Bypass capacitor connection is provided that allows
the user to achieve optimal noise performance at the output,
while the Error output functions as a diagnostic ag to
indicate that the output voltage has dropped more than 5%
below the nominal xed voltage.
Applications Information
External Capacitors – Selection
The FAN2502/03 allows the user to utilize a wide variety of
capacitors compared to other LDO products. An innovative
design approach offers signicantly reduced sensitivity to
ESR (Effective Series Resistance), which degrades regulator
loop stability in older designs. While the improvements fea-
tured in the FAN2502/03 family greatly simplify the design
task, capacitor quality still must be considered if the designer
is to achieve optimal circuit performance. In general,
ceramic capacitors offer superior ESR performance, at a
lower cost and a smaller case size than tantalums. Those with
X7R or Y5Vdielectric offer the best temperature coefcient
characteristics. The combination of tolerance and variation
over temperature in some capacitor types can result in signif-
icant variations, resulting in unstable performance over rated
conditions.
Input Capacitor
An input capacitor of 2.2F (nominal value) or greater,
connected between the Input pin and Ground, located in
close proximity to the device, will improve transient
response and noise rejection. Higher values will offer supe-
rior input ripple rejection and transient response. An input
capacitor is recommended when the input source, either a
battery or a regulated AC voltage, is located far from the
device. Any good quality ceramic, tantalum, or metal lm
capacitor will give acceptable performance, however tanta-
lum capacitors with a surge current rating appropriate to the
application must be selected to avoid catastrophic failure.
Output Capacitor
An output capacitor is required to maintain regulator loop
stability. Unlike many other LDO regulators, the FAN2502/
03 family of products are nearly insensitve to output capaci-
tor ESR. Stable operation will be achieved with a wide
variety of capacitors with ESR values ranging from 10m
to
10
or more. Tantalum or aluminum electrolytic, or multi-
layer ceramic types can all be used. A nominal value of at
least 1F is recommended.
Bypass Capacitor (FAN2502 Only)
In the xed-voltage conguration, connecting a capacitor
between the bypass pin and ground can signicantly reduce
noise on the output. Values ranging from 470pF to 10nF can
be used, depending on the sensitivity to output noise in the
application.
At the high-impedance Bypass pin, care must be taken in the
circuit layout to minimize noise pickup, and capacitors must
be selected to minimize current loading (leakage). Noise
pickup from external sources can be considerable. Leakage
currents into the Bypass pin will directly affect regulator
accuracy and should be kept as low as possible; thus, high-
quality ceramic and lm types are recommended for their
low leakage characteristics. Cost-sensitive applications not
concerned with noise can omit this capacitor.
Control Functions
Enable Pin
Applying a voltage of 0.4V or less at the Enable pin will
disable the output, reducing the quiescent output current to
less than 1A, while a voltage of 2.0V or greater will enable
the device. If this shutdown function is not needed, the pin
can simply be connected to the VIN pin. Allowing this pin to
oat will cause erratic operation.
Error Flag (FAN2503 only)
To indicate conditions such as input voltage dropout
(low VIN), overheating, or overloading (excessive output cur-
rent), the ERR pin indicates a fault condition. It is an open-
drain output which is HIGH when the voltage at VOUT is
greater than 95% of the nominal rated output voltage and
LOW when VOUT is less than 95% or the rated output volt-
age, as specied in the error trip level characteristics.
A logic pullup resistor of 100K
is recommended at this
output. The pin can be left disconnected if unused.
Thermal Protection
The FAN2502/03 is designed to supply high peak output cur-
rents of up to 1A for brief periods, however this output load
will cause the device temperature to increase and exceed
maximum ratings due to power dissipation. During output
overload conditions, when the die temperature exceeds the
shutdown limit temperature of 150°C, onboard thermal
protection will disable the output until the temperature drops
below this limit, at which point the output is then re-enabled.
During a thermal shutdown situation the user may assert the
power-down function at the Enable pin, reducing power
consumption to the minimum level IGND x VIN.
相关PDF资料 |
PDF描述 |
|---|---|
| FAN2504S26 | THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS |
| FAN2504S27 | VOLT REGULATOR|FIXED|+2.7V|CMOS|TSOP|6PIN|PLASTIC |
| FAN2504S28 | THREE-TERMINAL POSITIVE FIXED VOLTAGE REGULATORS |
| FAN2504S285 | VOLT REGULATOR|FIXED|+2.85V|CMOS|TSOP|6PIN|PLASTIC |
| FAN2504S30 | CCD Imaging ICs; Target Application: MFP/Scanner; Number of Pixels x Lines: 5400x6; Pixel Size (Micron): 5.25um; Resolution (dpi): 1200; Data Rate (Color/BW) (MHz): 10; Sensitivity (G; BW) (V/lx.s): 6.4 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN2504S25X | 功能描述:低压差稳压器 - LDO LDO Voltage RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| FAN2504S26 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Positive Fixed Voltage Regulator |
| FAN2504S26X | 功能描述:低压差稳压器 - LDO LDO Voltage RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| FAN2504S27 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:VOLT REGULATOR|FIXED|+2.7V|CMOS|TSOP|6PIN|PLASTIC |
| FAN2504S27X | 功能描述:低压差稳压器 - LDO LDO Voltage RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。