- 您现在的位置：买卖IC网 > PDF目录21993 > FAN2512S26X (Fairchild Semiconductor)IC REG LDO 2.6V .15A SOT23-5 PDF资料下载
参数资料
| 型号： | FAN2512S26X |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 3/10页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.6V .15A SOT23-5 |
| 产品变化通告： | Mold Compound Change 29/Sept/2008 |
| 标准包装： | 3,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.6V |
| 输入电压： | 最高 6.5V |
| 电压 - 压降（标准）： | 0.15V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 带卷 (TR) |
FAN2512/FAN2513
An Enable pin, available on all devices, allows the user to
shut down the regulator output to conserve power, reducing
supply current to less than 1μA. The output can then be
re-Enabled within 500μSec, ful?lling the fast power-cycling
needs of CDMA applications. Depending on the model
selected, other control and status functions are available at
pin 4 to enhance the operation of the device. The adjustable-
voltage versions utilize pin 4 to connect to an external
voltage divider which feeds back to the regulator error
ampli?er, thereby setting the voltage as desired. Two other
functions are available in the ?xed-voltage versions: in
noise-sensitive applications, an external Bypass capacitor
connection is provided that allows the user to achieve opti-
mal noise performance at the output, while the Error output
functions as a diagnostic ?ag to indicate that the output
voltage has dropped more than 5% below the nominal ?xed
voltage.
Applications Information
PRODUCT SPECIFICATION
more. Tantalum or aluminum electrolytic, or multilayer
ceramic types can all be used. A nominal value of at least
1μF is recommended.
Bypass Capacitor (FAN2512 Only)
In the ?xed-voltage con?guration, connecting a capacitor
between the bypass pin and ground can signi?cantly reduce
noise on the output. Values ranging from 470pF to 10nF can
be used, depending on the sensitivity to output noise in the
application.
At the high-impedance Bypass pin, care must be taken in the
circuit layout to minimize noise pickup, and capacitors must
be selected to minimize current loading (leakage). Noise
pickup from external sources can be considerable. Leakage
currents into the Bypass pin will directly affect regulator
accuracy and should be kept as low as possible; thus, high-
quality ceramic and ?lm types are recommended for their
low leakage characteristics. Cost-sensitive applications not
concerned with noise can omit this capacitor.
External Capacitors – Selection
The FAN2512/13 allows the user to utilize a wide variety of
capacitors compared to other LDO products. An innovative
design approach offers signi?cantly reduced sensitivity to
ESR (Effective Series Resistance), which degrades regulator
loop stability in older designs. While the improvements fea-
tured in the FAN2512/13 family greatly simplify the design
task, capacitor quality still must be considered if the designer
is to achieve optimal circuit performance. In general,
ceramic capacitors offer superior ESR performance, at a
lower cost and a smaller case size than tantalums. Those with
X7R or Y5Vdielectric offer the best temperature coef?cient
characteristics. The combination of tolerance and variation
over temperature in some capacitor types can result in signif-
icant variations, resulting in unstable performance over rated
conditions.
Input Capacitor
An input capacitor of 2.2μF (nominal value) or greater,
connected between the Input pin and Ground, located in
close proximity to the device, will improve transient
response and noise rejection. Higher values will offer supe-
rior input ripple rejection and transient response. An input
capacitor is recommended when the input source, either a
battery or a regulated AC voltage, is located far from the
device. Any good quality ceramic, tantalum, or metal ?lm
capacitor will give acceptable performance, however tanta-
lum capacitors with a surge current rating appropriate to the
application must be selected to avoid catastrophic failure.
Output Capacitor
An output capacitor is required to maintain regulator loop
stability. Unlike many other LDO regulators, the FAN2512/13
family of products are nearly insensitive to output capacitor
ESR. Stable operation will be achieved with a wide variety
of capacitors with ESR values ranging from 10m ? to 10 ? or
REV. 1.2.0 01/10/13
Control Functions
Enable Pin
Applying a voltage of 0.4V or less at the Enable pin will dis-
able the output, reducing the quiescent output current to less
than 1μA, while a voltage of 2.0V or greater will enable the
device. If this shutdown function is not needed, the pin can
simply be connected to the V IN pin. Allowing this pin to ?oat
will cause erratic operation.
Error Flag (FAN2513 Only)
To indicate conditions such as input voltage dropout
(low V IN ), overheating, or overloading (excessive output
current), the ERR pin indicates a fault condition. It is an
open-drain output which is HIGH when the voltage at V OUT
is greater than 95% of the nominal rated output voltage and
LOW when V OUT is less than 95% or the rated output volt-
age, as speci?ed in the error trip level characteristics.
A logic pullup resistor of 100K ? is recommended at this
output. The pin can be left disconnected if unused.
Thermal Protection
The FAN2512/13 is designed to supply high peak output
currents of up to 1A for brief periods, however this output
load will cause the device temperature to increase and
exceed maximum ratings due to power dissipation. During
output overload conditions, when the die temperature
exceeds the shutdown limit temperature of 150°C, onboard
thermal protection will disable the output until the tempera-
ture drops below this limit, at which point the output is then
re-enabled. During a thermal shutdown situation the user
may assert the power-down function at the Enable pin,
reducing power consumption to the minimum level I GND .
3
相关PDF资料 |
PDF描述 |
|---|---|
| NSR0320MW2T1G | DIODE SCHOTTKY 1A 20V SOD-323 |
| 8309-8009 | CONN D-SUB RCPT 9POS W/O INSERT |
| FAN2559MP18X | IC REG LDO 1.8V .18A 6MLP |
| EBM15DRKI-S13 | CONN EDGECARD 30POS .156 EXTEND |
| VE-B6X-CX | CONVERTER MOD DC/DC 5.2V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN2512S27 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:VOLT REGULATOR|FIXED|+2.7V|CMOS|TSOP|6PIN|PLASTIC |
| FAN2512S27X | 功能描述:低压差稳压器 - LDO LDO Voltage RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| FAN2512S28 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Positive Fixed Voltage Regulator |
| FAN2512S285 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:VOLT REGULATOR|FIXED|+2.85V|CMOS|TSOP|6PIN|PLASTIC |
| FAN2512S285X | 功能描述:低压差稳压器 - LDO LDO Voltage RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。