- 您现在的位置：买卖IC网 > PDF目录1790 > FAN4855MTCX (Fairchild Semiconductor)IC REG BST SYNC ADJ 0.5A 8TSSOP PDF资料下载
参数资料
| 型号： | FAN4855MTCX |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BST SYNC ADJ 0.5A 8TSSOP |
| 产品变化通告： | Product Discontinuation 03/Dec/2009 |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 3 V ~ 5 V |
| 输入电压： | 1.6 V ~ 4.5 V |
| 电流 - 输出： | 500mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-TSSOP |
The synchronous recti?er signi?cantly improves ef?-
ciency without the addition of an external component, so
that conversion ef?ciency can be as high as 94% over a
large load range, as shown in the Typical Operating
Characteristics. Even at light loads, the ef?ciency stays
high because the switching losses of the converter are
minimized by reducing the switching frequency.
Error Detection Comparator (LBI – LBO)
An additional comparator A3 is provided to detect low V IN
or any other error conditions that is important to the user.
The non-inverting input of the comparator is internally
connected to a reference threshold voltage V th while the
inverting input is connected to the LBI pin. The output of
the low battery comparator is a simple open-drain output
that goes active low if the battery voltage drops below
the programmed threshold voltage on LBI. The output
requires a pull-up resistor having a recommended value
of 100 k ? , should be connected only to V OUT .
The low-battery detector circuit is typically used to super-
vise the battery voltage and to generate an error ?ag or a
RESET command when the battery voltage drops below
a user-set threshold voltage. The function is active only
when the device is enabled. When the device is disabled,
the LBO-pin is high impedance.
Shutdown
The device enters shutdown when V SHDN is approxi-
mately less than 0.5V IN . During shutdown the regulator
stops switching, all internal control circuitry including the
low-battery comparator is switched off and the load is
The battery voltage, at which the detection circuit
switches, can be programmed with a resistive divider
connected to the LBI-pin. The resistive divider scales
down the battery voltage to a voltage level of tenths of
volt, which is then compared to the LBI threshold voltage.
The LBI-pin has a built-in hysteresis of 25 mV. The resis-
tor values R1 and R2 can be calculated using the follow-
ing equation:
V IN_MIN = 0.39 x (R1+R2)/R2
The value of R2 should be 270k or less to minimize bias
current errors. R1 is then found by rearranging the equa-
tion:
R1 = R2 x (V IN_MIN /0.39 – 1)
If the low-battery detection circuit is not used, the LBI-pin
should be connected to GND (or to V IN ) and the LBO-pin
can be left unconnected or tied to GND. Do not let the
LBI-pin ?oat.
Component Selection
Input and Output Capacitors Selection
For common general purpose applications, 47μF tanta-
lum capacitors are recommended. Ceramic capacitors
are recommended at input only; if connected at the out-
put they cannot improve signi?cantly the voltage ripple.
More effective in reducing the output ripple at light load is
to connect a small capacitor of 18 to 100pF between
V OUT and FB pin.
Table 1. Recommended capacitors
disconnected from the input. The output voltage may
drop below the input voltage during shutdown. The typi-
cal dependence shutdown voltage versus input voltage
and the timing process of the exiting shutdown are
shown on the Diagrams. For normal operation V SHDN
should be driven up 0.8V IN or connected to the V IN .
Application Information
Vendor
MuRata
AVX
Sprague
Kemet
Description
X5R Ceramic
TAJ,TPS series tantalum
595D series tantalum
T494 series tantalum
Selecting the Output Voltage
The output voltage V OUT can be adjusted from 3V to 5V,
choosing resistors R4 and R5 of the divider in the feed-
back circuit (see Test Circuit). The value of the R5 is rec-
ommended to be less than 270k. R4 can be calculated
using the following equation:
R4 = R5[(V OUT /V REF ) – 1]
where V REF = 1.24V
Inductor Selection
The inductor parameters directly in?uencing the device
performance are the saturation current and the DC resis-
tance. The FAN4855 operates with a typical inductance
of 10μH. The lower the resistance, the higher the ef?-
ciency. The saturation current should be rated higher
than 0.8A, which is the typical threshold to switch off the
N-channel power FET.
Table 2. Recommended Inductors
Setting the LBI Threshold of Low-Battery
Detector Circuit
The LBO-pin goes active low when the voltage on the
LBI-pin decreases below the set threshold typical voltage
of 390 mV, which is set by to the internal reference volt-
age.
FAN4855 Rev. 1.0.1
9
Supplier
MuRata
Coilcraft
Coiltronics
Sumida
Manufacturer Part Number
LQ66C100M4
DT1608C-103
UP1B100
CDR63B-100
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FAN4860UC33X | IC REG BST SYNC 3.3V 0.2A 6WLCSP |
| FAN5026MTC | IC CONTROLLER DDR 28TSSOP |
| FAN5234MTCX | IC PWM CTLR/PFM MOBILE 16TSSOP |
| FAN5236MTC | IC DDR/PWM CTRLR DUAL 28TSSOP |
| FAN5350MPX | IC REG BUCK SYNC 1.82V 0.6A 6MLP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN4855MTCX | 制造商:Fairchild Semiconductor Corporation 功能描述:DC/DC Converter IC |
| FAN4855MU | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:500mA High Efficiency Boost Regulator with Adjustable Output, Shutdown and Low Battery Detect |
| FAN4855MUX | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:500mA High Efficiency Boost Regulator with Adjustable Output, Shutdown and Low Battery Detect |
| FAN4858TZ | 功能描述:数字总线开关 IC 600mA Ultralow Input Voltage Boost Switch RoHS:否 制造商:Texas Instruments 开关数量:24 传播延迟时间:0.25 ns 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:TSSOP-56 封装:Reel |
| FAN4860 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:3MHz, 5V Output Synchronous TinyBoosta?￠ Regulator |
发布紧急采购，3分钟左右您将得到回复。