- 您现在的位置：买卖IC网 > PDF目录67412 > FAN5037MX_NL (FAIRCHILD SEMICONDUCTOR CORP) SWITCHING CONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | FAN5037MX_NL |
| 厂商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO8 |
| 封装： | LEAD FREE, SOIC-8 |
| 文件页数： | 10/11页 |
| 文件大小： | 101K |
| 代理商： | FAN5037MX_NL |
FAN5037
PRODUCT SPECIFICATION
8
REV. 1.0.3 9/26/01
where TF = Tolerance Factor for the sense resistor and 0.6A
accounts for the inductor ripple current.
Since the value of the sense resistor is often less than 10m
,
care should be taken in the layout of the PCB. Trace resis-
tance can contribute signicant errors. The traces to the
IFBH and IFBL pins of the FAN5037 should be Kelvin con-
nected to the pads of the current-sense resistor. To minimize
the inuence of noise, the two traces should be run next to
each other.
Schottky Diode
In Figure 1, MOSFET Q1 and yback diode D1 are used as
complementary switches in order to maintain a constant cur-
rent through the output inductor L2. As a result, D1 will have
to carry the full current of the output load when the power
MOSFET is turned off. The power in the diode is a direct
function of the forward voltage at the rated load current dur-
ing the off time of the FET. The following equation can be
used to estimate the diode power:
where ID is the forward current of the diode, VD is the for-
ward voltage of the diode, and DutyCycle is dened the
same as
For the Motorola MBRB1545CT Rectier in Figure 1,
It is recommended that the diode T0-220 package be
attached to a heatsink.
Board Design Considerations
MOSFET Placement
Placement of the power MOSFET is critical in the design of
the switch-mode regulator. The MOSFET should be placed
in such a way as to minimize the length of the gate drive path
from the FAN5037 SDRV pin. This trace should be kept
under 0.5" for optimal performance. Excessive lead length
on this trace will cause high frequency noise resulting from
the parasitic inductance and capacitance of the trace. Since
this voltage can transition nearly 12V in around 100nsec, the
resultant ringing and noise would be very difcult to sup-
press. This trace should be routed on one layer only and kept
well away from the “quiet” analog pins of the device: CEXT,
IFBH, IFBL, and GND. Refer to Figure 2. A 4.7
resistor in
series with the MOSFET gate can decrease this layout criti-
cality. Refer to Figure 1.
Inductor and Schottky Diode Placement
The inductor and y-back Schottky diode need to be placed
close to the source of the power MOSFET for the same rea-
sons stated above. The node connecting the inductor and
Schottky diode will swing between the drain voltage of the
FET and the forward voltage of the Schottky diode. It is rec-
ommended that this node be converted to a plane if possible.
This node will be part of the high current path in the design,
and as such it is best treated as a plane in order to minimize
the parasitic resistance and inductance on that node. Since
most PC board manufacturers utilize 1/2 oz copper on the
top and bottom signal layers of the PCB, it is not recom-
mended to use these layers to route the high current portions
of the regulator design. Since it is more common to use 1 oz.
copper on the PCB inner layers, it is recommended to use
those layers to route the high current paths in the design.
P
DIODE
I
D
V
D
1
DutyCycle
–
()
×
=
Duty Cycle
Vout
Vin
-------------
=
P
DIODE
10A
0.65
1
73.1%
–
()
×
1.75W
==
Figure 3. Examples of good and poor layouts
5
6
7
8
5
= "Quiet" Pins
6
7
4
3
2
81
4
3
2
1
Example of
a Good Layout
Example of
a Problem Layout
Noisy signal radiates
onto quiet pins and the
trace is too long.
Gate resistor is far away
from the MOSFET.
Noisy signal is routed
away from quiet pins and the
trace length is kept under 0.5in.
The gate resistor is as close
as possible to the MOSFET.
相关PDF资料 |
PDF描述 |
|---|---|
| FAN5037M_NL | SWITCHING CONTROLLER, PDSO8 |
| FAN5061M | SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO20 |
| FAN5201MSA | 6 A BATTERY CHARGE CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO24 |
| FAN5361UMP10X | SWITCHING REGULATOR, DSO6 |
| FAN5361UC13X | SWITCHING REGULATOR, PBGA6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN5038 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Dual Voltage Controller for DSP Power |
| FAN5038M | 功能描述:数字信号处理器和控制器 - DSP, DSC Dual Volt Controller DSP Power RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| FAN5038MX | 功能描述:数字信号处理器和控制器 - DSP, DSC Dual Volt Controller DSP Power RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| FAN503MTCX | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5056MV85 | 功能描述:DC/DC 开关控制器 SOIC-WIDE-24 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。