- 您现在的位置：买卖IC网 > PDF目录68993 > FAN5056MV90 (FAIRCHILD SEMICONDUCTOR CORP) SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO24 PDF资料下载
参数资料
| 型号： | FAN5056MV90 |
| 厂商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO24 |
| 封装： | SOIC-24 |
| 文件页数： | 6/18页 |
| 文件大小： | 163K |
| 代理商： | FAN5056MV90 |
FAN5056V85/FAN5056V90
PRODUCT SPECIFICATION
14
REV. 1.0.2 3/28/01
controller to reduce the converter’s duty cycle to approxi-
mately 20%. This causes a drastic reduction in the output
voltage as the load regulation collapses into the short circuit
control mode. With a 4m
output short, the voltage is
reduced to 29A * 4m
= 116mV. The output voltage does
not return to its nominal value until the output current is
reduced to a value within the safe operating range for the
DC-DC converter.
Schottky Diode Selection
The application circuits of Figure 1-5 shows a Schottky
diode, D2, which is used as a free-wheeling diode to assure
that the body-diode in Q2 does not conduct when the upper
MOSFET is turning off and the lower MOSFET is turning
on. It is undesirable for this diode to conduct because its high
forward voltage drop and long reverse recovery time
degrades efciency, and so the Schottky provides a shunt
path for the current. Since this time duration is very short,
the selection criterion for the diode is that the forward volt-
age of the Schottky at the output current should be less than
the forward voltage of the MOSFET’s body diode.
Output Filter Capacitors
The output bulk capacitors of a converter help determine its
output ripple voltage and its transient response. It has
already been seen in the section on selecting an inductor that
the ESR helps set the minimum inductance, and the capaci-
tance value helps set the maximum inductance. For most
converters, however, the number of capacitors required is
determined by the transient response and the output ripple
voltage, and these are determined by the ESR and not the
capacitance value. That is, in order to achieve the necessary
ESR to meet the transient and ripple requirements, the
capacitance value required is already very large.
The most commonly used choice for output bulk capacitors
is aluminum electrolytics, because of their low cost and low
ESR. The only type of aluminum capacitor used should be
those that have an ESR rated at 100kHz. Consult Application
Bulletin AB-14 for detailed information on output capacitor
selection.
The output capacitance should also include a number of
small value ceramic capacitors placed as close as possible to
the processor; 0.1F and 0.01F are recommended values.
Input Filter
The DC-DC converter design may include an input inductor
between the system +5V supply and the converter input as
shown in Figure 5. This inductor serves to isolate the +5V
supply from the noise in the switching portion of the DC-DC
converter, and to limit the inrush current into the input capac-
itors during power up. A value of 2.5H is recommended.
It is necessary to have some low ESR aluminum electrolytic
capacitors at the input to the converter. These capacitors
deliver current when the high side MOSFET switches on.
Figure 5 shows 3 x 1000F, but the exact number required
will vary with the speed and type of the processor. For the
top speed Katmai and Coppermine, the capacitors should be
rated to take 9A and 6A of ripple current respectively.
Capacitor ripple current rating is a function of temperature,
and so the manufacturer should be contacted to nd out the
ripple current rating at the expected operational temperature.
For details on the design of an input lter, refer to Applica-
tions Bulletin AB-15.
Figure 5. Input Filter
Programmable Active Droop
The FAN5056 includes Programmable Active Droop: as
the output current increases, the output voltage drops, and
the amount of this drop is user adjustable. This is done in
order to allow maximum headroom for transient response of
the converter. The current is typically sensed by measuring
the voltage across the RDS,on of the high-side MOSFET
during its on time, as shown in Figures 1 and 2.
To program the amount of droop, use the formula
where Imax is the current at which the droop occurs, and
Rsense is the resistance of the current sensor, either the source
resistor or the high-side MOSFET’s on-resistance. For exam-
ple, to get 120mV of droop with a maximum output current
of 30A and a 10m
sense resistor, use R
D = 14.4K * 30A *
10m
/(120mV * 9) = 4K. The value of the product
Imax*Rsense must be < 600mV for proper functioning of
the droop circuit. If this product is exceeded, a lower resis-
tance MOSFET must be used. Further details on use of the
Programmable Active Droop may be found in Applications
Bulletin AB-24.
Remote Sense
The FAN5056 offers remote sense of the output voltage to
minimize the output capacitor requirements of the converter.
It is highly recommended that the remote sense pin, Pin 8, be
tied directly to the processor power pins, so that the effects
of power plane impedance are eliminated. Further details on
use of the remote sense feature of the FAN5056 may be
found in Applications Bulletin AB-24.
2.5
H
5V
0.1
F
1000
F, 10V
Electrolytic
Vin
RD
14.4K
*I
max *Rsense
VDroop *9
相关PDF资料 |
PDF描述 |
|---|---|
| FAN5056V85M | SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO24 |
| FAN5056V90M | SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO24 |
| FAN5090MTCX_NL | 3 A SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO24 |
| FAN5093MTCX_NL | 3 A SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO24 |
| FAN5093MTC | |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN5059 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:High Performance Programmable Synchronous |
| FAN5059_BBA3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5059M | 功能描述:开关变换器、稳压器与控制器 DC-DC Controller HP Programmable Sync RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| FAN5059M_Q | 功能描述:开关变换器、稳压器与控制器 DC-DC Controller HP Programmable Sync RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| FAN5059MX | 功能描述:开关变换器、稳压器与控制器 DC-DC Controller HP Programmable Sync RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。