- 您现在的位置：买卖IC网 > PDF目录20687 > FAN5331SX_Q (Fairchild Semiconductor)IC LED DRVR WHITE BCKLGT SOT23-5 PDF资料下载
参数资料
| 型号： | FAN5331SX_Q |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHITE BCKLGT SOT23-5 |
| 标准包装： | 3,000 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 通用 |
| 频率： | 1.15MHz ~ 1.85MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出电压： | 20V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
The inductor saturation current should be rated around 1A,
which is the threshold of the internal current limit circuit. This
limit is reached only during the start-up and with heavy load
condition; when this event occurs the converter can shift over in
discontinuous conduction mode due to the automatic turn-off of
the switching transistor, resulting in higher ripple and reduced
ef?ciency.
Some recommended inductors are suggested in the table
below:
Inductor
PCB Layout Recommendations
The inherently high peak currents and switching frequency of
power supplies require careful PCB layout design. Therefore,
use wide traces for high current paths and place the input
capacitor, the inductor, and the output capacitor as close as
possible to the integrated circuit terminals. The resistor divider
that sets the output voltage should be routed away from the
inductor to avoid RF coupling. A four layer PCB with at least one
ground plane connected to the pin 2 of the IC is recommended.
This ground plane acts as an electromagnetic shield to reduce
EMI and parasitic coupling between components.
Value
10μH
Vendor
Panasonic
Part Number
ELL6GM100M
Comment
Lower Pro?le
(1.6mm)
10μH
Murata
LQS66SN100M03L
Highest
Ef?ciency
10μH
Coilcraft
DO1605T-103Mx
Small Size
Table 1: Recommended Inductors
Capacitors Selection
For best performance, low ESR input and output capacitors are
required. Ceramic capacitors in the range 4.7μF to 10μF, placed
as close to the IC pins, are recommended for the lower input
and output ripple. The output capacitor voltage rating should be
according to the V OUT setting.
A feed forward capacitor C F , is required for stability. The recom-
mended value (R 1 x C F ) is around 18μS. Some capacitors are
suggested in the table below.
Capacitor
Figure 5. Recommended Layout
Application Examples
1. LED Driver
One or more serial LED strings can be driven with a constant
current, set by the series resistor, given by
I LED = ----------------
Value
4.7μF
4.7μF
Vendor
Panasonic
Murata
Part Number
ECJ3YB1C475K
GRM31CR61C475
1.23V
R1
Table 2: Recommended Capacitors
Diode Selection
V IN
C IN
2.7V to 5.5V
L
10 μ H
BAT54
C OUT
V OUT
The external diode used for recti?cation is usually a Schottky
4.7 μ F
4.7 μ F
diode. Its average forward current and reverse voltage maxi-
mum ratings should exceed the load current and the voltage at
the output of the converter respectively. A barrier Schottky diode
such as BAT54 is preferred, due to its lower reverse current over
5
V
IN
SW
FB
1
3
the temperature range.
Care should be taken to avoid any short circuit of V OUT to GND,
ON
OFF
4
SHDN
GND
2
R1
R2
even with the IC disabled, since the diode can be instantly dam-
aged by the excessive current.
Thermal Shutdown
When the die temperature exceeds 150°C, a reset occurs and
will remain in effect until the die cools to 130°C, at that time the
circuit will be allowed to restart.
FAN5331 Rev. 1.0.1
7
Figure 6. Low Noise Boost LED Driver
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JNW-CX-F3 | CONVERTER MOD DC/DC 5.5V 75W |
| ABC36DRYH-S93 | CONN EDGECARD 72POS DIP .100 SLD |
| AISC-0603-R12G-T | INDUCTOR CHIP 120NH 2% SMD |
| RBA15DTKS | CONN EDGECARD 30POS DIP .125 SLD |
| RMC40DRXS-S734 | CONN EDGECARD 80POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN5332_BBC3086B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5332A | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:High Efficiency, High Current Serial LED Driver and OLED Supply with 30V Integrated Switch |
| FAN5332ASX | 功能描述:直流/直流开关转换器 1.6MHz BOOST REGULATOR RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| FAN5332ASX_NL | 功能描述:LED照明驱动器 1.6MHz Boost regulator RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| FAN5333A | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:High Efficiency, High Current Serial LED Driver with 30V Integrated Switch |
发布紧急采购，3分钟左右您将得到回复。