参数资料
| 型号： | FAN7093 |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 8/14页 |
| 文件大小： | 0K |
| 描述： | IC DIODE HALF BRIDGE PN D2PAK-7 |
| 标准包装： | 800 |
| 类型： | 半桥 |
| 输入类型： | 非反相 |
| 输出数： | 1 |
| 导通状态电阻： | 12.3 毫欧 |
| 电流 - 输出 / 通道： | 46A |
| 电流 - 峰值输出： | 88A |
| 电源电压： | 5.5 V ~ 28 V |
| 工作温度： | -40°C ~ 150°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-8，D²Pak（7 引线+接片），TO-263CA |
| 供应商设备封装： | TO-263（D2Pak） |
| 包装： | 带卷 (TR) |
Protection Functions
The device provides several integrated protection
functions designed to prevent IC damage in fault
conditions. Fault conditions are considered as “outside”
the normal operating range. Protection functions are not
for continuous or repetitive operation, with the exception
of current-limit protection. In a fault condition, the
FAN7093 applies the highest slew rate possible,
independent of the connected slew rate resistor (R SR ).
Over-voltage, over-temperature, and over-current
situations are indicated by a fault current flag I IS(LIM) at
the IS pin. The following describes the protection
functions in order of priority. Over-voltage protection
overrides all other protections.
Over-Voltage Protection (OVP)
To ensure a high immunity against over-voltage
conditions like load dump, the device turns off the low-
side MOSFET and turns on the high-side MOSFET
when the supply voltage exceeds the over-voltage
protection level V OV(OFF) . The control IC returns to
normal operation t lock =140 μs (Typ.) after the supply
voltage decreases below the over-voltage lockout level,
V OV(ON). In H-bridge configurations, this behavior leads to
freewheeling in the high side during over-voltage
condition. If the load current exceeds I CP in over-voltage
lockout, the IC turns off the high-side driver and latches
this state. See Table 1, which shows the condition of the
Current Limitation
The current is measured in both MOSFETS. As soon as
the current reaches the limit I CL , the low-side or high-
side MOSFET is deactivated and the other MOSFET
activated for t CLS . During that time, changes at the IN pin
are ignored. The /INH pin can still be used to turn off
both MOSFETs. After t CLS , the MOSFETS return to their
initial setting. The error signal at the IS pin is reset after
2 x t CLS . Unintentional triggering of the current-limit
circuitry through short current spikes (e.g. inflicted by
EMI coming from a motor) is suppressed by an internal
filter. Reaction delay of the filter circuitry affects the
current limit level I CL , depending on slew rate of the load
current dI/dt.
IS pin flag. This state can be reset (if the conditions no
longer exist) when /INH goes from HIGH to LOW to
HIGH again.
Figure 5.
Current Limitation Timing Diagram
(Inductive Load)
Under-Voltage Protection (UVP)
To avoid uncontrolled motion; for example, a driven
motor at low voltages; the control IC turns off all
MOSFETS when the supply voltage drops below the
turn-off voltage, V UV(OFF) . The control IC resumes to
normal operation when the supply voltage rises above
the turn-on voltage V UV(ON) . Notice that the IS pin does
NOT flag this fault condition.
Over-Temperature Protection (OTP)
The FAN7093 is protected against over-temperature by
an integrated temperature sensor in the control IC.
Over-temperature protection turns off both output
stages. This state is latched until the device is reset by a
In combination with a typical inductive load, such as a
motor, this results in a switched-mode current limitation.
This method of limiting current has the advantage of
greatly reduced power dissipation compared to driving
the MOSFET in linear mode. Therefore, it is possible to
use the current limitation for a short time without
exceeding the maximum allowed junction temperature
(e.g. for limiting the inrush current during motor startup).
However, regular use of the current limitation is only
allowed as long as the specified maximum junction
temperature is not exceeded. Exceeding this
temperature reduces the life of the device.
Short-Circuit Protection (SCP)
The device is short-circuit protected against:
LOW signal with a minimum pulse length of t reset at the
/INH pin, assuming the control IC temperature
decreased by at least the thermal hysteresis. Repetitive
?
?
Output Shorted to Ground
Output Shorted to Battery Voltage
use of the over-temperature protection decreases
product life.
? 2011 Fairchild Semiconductor Corporation
FAN7093 ? Rev. 1.0.5
8
? Short-Circuit between the Load Connections
The short-circuit protection is a combination of current
limit and over-temperature shutdown of the device.
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FAN7313M | IC DRIVER GATE HALF BRIDG 20SOIC |
| FAN7317BM | IC DVR LCD BKLT INVERTER 20-SOIC |
| FAN7318AM | IC DVR LCD BKLT INVERTER 16-SOIC |
| FAN7318BMX | IC DVR LCD BKLT INVERTER 20-SOIC |
| FAN7319M | IC DVR LCD BKLT INVERTER 20-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN7093_12 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:High-Current PN Half-Bridge Driver |
| FAN7093_F085 | 功能描述:功率驱动器IC Half Bridge Rect 47A RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| FAN7093_FO85 | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN7171 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:High-Current High-Side Gate Drive IC |
| FAN7171_F085 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:New Products, Tips and Tools for Power and Mobile Applications |
发布紧急采购，3分钟左右您将得到回复。