- 您现在的位置：买卖IC网 > PDF目录15081 > FAN7554D (Fairchild Semiconductor)IC REG CTRLR FLYBK ISO PWM 8SOIC PDF资料下载
参数资料
| 型号： | FAN7554D |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 8/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR FLYBK ISO PWM 8SOIC |
| 标准包装： | 95 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 500kHz |
| 占空比： | 98% |
| 电源电压： | 9 V ~ 30 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -25°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 其它名称： | FAN7554D_NL FAN7554D_NL-ND |
FAN7554
Operation Description
The FAN7554 has all the basic features of the current mode SMPS control IC. Its basic configuration includes the UVLO with
6V hysteresis, a band gap reference, the oscillator that can oscillate up to 500kHz according to R t /C t (connected externally), a
PWM logic circuit , a gate driver, and the feedback circuit that has the current source and soft start function. The FAN7554 has
various functions such as an over load protection, an over current protection, and an over voltage protection. The over load
protection forces the FAN7554 to stop its operation if the load current is higher than the preset value. The protection circuit
can also be prevented from operating during transient states by ensuring that a certain amount of the time passes before the
protection circuit operates. The shutdown circuit is configured for an auto-restart, so the FAN7554 automatically restarts when
Vcc drops to 9V (stop voltage).
Start-Up
The start-up circuit is made up of an under voltage lock out (UVLO), the protection for low voltage conditions, and the 5V
reference (V ref ), which supplies bias voltage to the control circuit after start-up. The start voltage of the UVLO is 15V , and
the stop voltage after turn on is 9V. It has a 6V hysteresis. The minimum operating current for start-up threshold is typically
100uA, and this can reduce the power dissipation on the start-up resistor. The Vref is composed of the band gap reference
circuit with its superior temperature characteristics and supplies power to all the FAN7554 circuits and R t /C t , with the
exceptions of the ULVO circuit and ON/OFF control circuit.
DC Link
Icc(mA)
7
VCC
UVLO
5V
Vref
Internal bias
Good logic
7.0
15V/9V
FAN7554
0.01
9
15
Vcc (V)
Figure 11. Low Current Start-Up & Bandgap Reference Circuit
Figure 12. Start-Up & Circuit Characteristics
Soft Start
The SMPS output load usually contains a capacitive load component. During initial start-up, the output voltage increases at a
fixed time constant because of this component. If the feedback loop, which controls the output voltage, was to start without
the soft start circuit, the feedback loop would appear to be open during initial start-up , so, at start-up, the feedback voltage
applied to the PWM comparator ’s inverting input (-) reaches its maximum value(1V).
During this time, the peak value of the drain current would stay at the maximum value, and the maximum power would be
delivered to the secondary load side from the start. When the maximum power is delivered to the secondary side for this initial
fixed time, the entire circuit is seriously stressed. The use of a soft start can avoid such stresses. At start-up, the soft start
capacitor Cs is charged by 1mA and 100uA current sources.
The voltage of the inverting terminal of the PWM comparator increases to 1/3 of the Cs voltage at a fixed time constant.
Subsequently, the drain peak current is limited by the gradual increase in the Cs voltage and this causes the output voltage to
increase smoothly. When the Cs voltage becomes greater than 3V, the diode Ds turns off consequently, the feedback capacitor
Cfb is charged by 1mA and 5uA current sources. This charge voltage determines the comparator ’s inverting voltage. Then, Cs
voltage charges to 5V by 100uA current source. The soft start capacitor Cs is discharged when the UVLO good logic starts, so
the soft start is repeated at re-start.
8
相关PDF资料 |
PDF描述 |
|---|---|
| X5083S8IZ-2.7 | IC SUPERVISOR CPU 8K EE 8-SOIC |
| GCC50DCSN-S288 | CONN EDGECARD 100POS .100 EXTEND |
| APSG200ELL681MJB5S | CAP ALUM 680UF 20V 20% RADIAL |
| GCC50DCSH-S288 | CONN EDGECARD 100POS .100 EXTEND |
| UVR0J223MRD6 | CAP ALUM 22000UF 6.3V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN7554D_Q | 功能描述:电流型 PWM 控制器 PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| FAN7554DTF | 功能描述:DC/DC 开关控制器 PWM Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| FAN7554DTF_Q | 功能描述:电流型 PWM 控制器 PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| FAN7556 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Voltage Mode PWM Controller |
| FAN7556M | 功能描述:电压模式 PWM 控制器 PWM Control IC IVM RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。