- 您现在的位置：买卖IC网 > PDF目录18773 > FCTN-RLY4-418-2 (Linx Technologies Inc)MODULE 4 POS RECEIVER 418MHZ PDF资料下载
参数资料
| 型号： | FCTN-RLY4-418-2 |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 2/7页 |
| 文件大小： | 0K |
| 描述： | MODULE 4 POS RECEIVER 418MHZ |
| 标准包装： | 1 |
| 系列： | LR |
| 功能： | 接收器，继电器 |
| 调制或协议： | OOK |
| 频率： | 418MHz |
| 应用： | 通用 |
| 接口： | 接收器，锁存输出 |
| 灵敏度： | -112dBm |
| 特点： | 4 位置 |
| 电源电压： | 7 V ~ 30 V |
ELECTRICAL SPECIFICATIONS
THEORY OF OPERATION
Parameter
Designation
Min.
Typical
Max.
Units
Notes
The FCTN-RLY4-***-2 module
POWER SUPPLY
combines the popular Linx LR
Operating Voltage
Supply Current
RX Only
RX and 1 Relay
RX and 2 Relays
RX and 3 Relays
RX and 4 Relays
V CC
I CC
7.0
4.0
16.0
26.0
35.0
45.0
–
7.0
36.0
65.0
95.0
125.0
30.0
15.0
65.0
120.0
175.0
225.0
VDC
mA
mA
mA
mA
mA
–
1
1
1
1
1
Series receiver with a decoder IC
and four relays that are capable of
switching a variety of AC or DC
loads. The Relay Function Module
is designed to receive a wireless
signal transmitted from a
compatible Linx RF module or pre-
RECEIVER SECTION
certified OEM transmitter. When
Receive Frequency Range
FCTN-RLY4-315
FCTN-RLY4-418
FCTN-RLY4-433
Center Frequency Accuracy
Receiver Sensitivity
F C
–
–
–
–
–
-50
-106
315
418
433.92
–
-112
–
–
–
+50
-118
MHz
MHz
MHz
kHz
dBm
–
–
–
–
3
transmitted data is received, the
data is presented to the decoder.
The decoder detects the logic states
of the DIP switch address lines, and
if they match the address settings of
the encoder, the decoder’s outputs
RELAY CHARACTERISTICS
are set to replicate the state of the
Arrangement
–
SPST
encoder’s data lines. Figure 3
Switched Power
–
–
–
–
–
–
480
4000
watts
VA
–
–
shows the inside of the module. The
four position DIP switch, S2, allows
Relay Switching Voltage
–
–
0.0
0.0
–
–
30.0
300.0
VDC
VAC
–
–
each relay to be set to latched (LAT)
or momentary (MOM) operation.
Figure 3: Latched / Momentary DIP Switch
Switched Device Current
Operate Time
–
–
0.6
–
–
10.0
7.0
–
A
mS
–
–
POWER SUPPLY CONSIDERATIONS
Release Time
Life Expectancy
Mechanical
Electrical
Contact Dielectric Strength
(at sea level for 1 minute)
ENVIRONMENTAL
Operating Temperature Range
–
–
–
–
–
–
– 5.0 –
1x10 7
1x10 5 @ 10A, 277VA
1000Vrms across contacts
1750Vrms contact-to-coil
-40 – +70
mS
Operations
° C
–
2
2
The module should be powered from a DC source that is free of noise and high
ripple. The best results are normally obtained using a battery or high quality AC
wall adapter capable of providing the supply currents indicated in the Electrical
Specifications section. Two supply connection options are provided: black
(ground) and red (+) quick-connect terminals or a barrel jack (for a 5.5mm shell,
2.1mm tip plug, tip +7 to 30VDC, shell ground). Only one connection should be
used at a time and proper supply polarity should be observed.
Storage Temperature Range
-45
–
+70
° C
2
SETTING THE MODULE ADDRESS
Notes
1. Typical values at 12V and 25 ° C; Max and Min values are over the full voltage and temperature range.
2. Characterized, but not tested.
3. For BER of 10 -5 at 1,200bps.
RELAY FUNCTION MODULE FEATURES
1. Antenna
The Relay Function Module provides
a total of 256 unique addreses to
avoid contention with other units or
to create unique relationships.
Address selection is made via eight
externally accessible DIP switches
2. DC Power Connector (7 to 30VDC)
3. “Quick-Connect” Alternate DC Input
4. Switched Device Connectors
1
as shown in the adjacent figure.
If the switch is on, the address line is
connected to ground, otherwise it is
floating. The transmitter’s address
5. Address Selector DIP Switches
4
3
2
5
must match exactly in order for the Figure 4: Address DIP Switches
units to communicate. Application
Note AN-00300 describes in detail how to set the address to match any of the
Holtek-based transmitters offered by Linx. This application note can be found in
Page 2
Figure 2: Relay Module Features
the Support section of the Linx website, www.linxtechnologies.com.
Page 3
相关PDF资料 |
PDF描述 |
|---|---|
| 31805 | DERFUSB-23E00 |
| FI212C245036-T | FILTER BALANCE 2.4GHZ BLUETOOTH |
| ME501206 | DIODE MOD 3PH BRDG 1200V 60A |
| MTCMR-EV2-GP-N2 | MODEM CELLULAR EV-DO DUAL |
| MTCMR-EV2-GP-N16 | MODEM CELLULAR EV-DO DUAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FCTN-RLY4-418-MOM | 功能描述:射频模块 4 Relay Rcvr Mod 418MHzMomentry Outpt RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| FCTN-RLY4-433 | 功能描述:射频模块 4 Relay Receiver Module 433MHz RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| FCTN-RLY4-433-2 | 功能描述:射频模块 4 Relay Receiver Module 433MHz ver 2 RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| FCTN-RLY4-433-MOM | 功能描述:射频模块 4 Relay Rcvr Mod 433MHzMomentry Outpt RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| FCTN-RLY4XX-433-MOM | 功能描述:MODULE 4 RELAY RECEIVER 433MHZ RoHS:否 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:- 标准包装:5 系列:MultiModem® iCell 功能:收发器，HSPA，调制解调器 调制或协议:GPRS，GSM，EDGE 频率:850MHz，900MHz，1.8GHz，1.9GHz 应用:- 接口:RS-232，USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V，USB 其它名称:881-1125 |
发布紧急采购，3分钟左右您将得到回复。