- 您现在的位置：买卖IC网 > PDF目录375795 > FGP20N6S2D (FAIRCHILD SEMICONDUCTOR CORP) Switch Mode Power Supply; Output Power:300W; No. of Outputs:1; Output 1 VDC +:5VDC; Output Current 1:60A; Power Supply Mounting:Chassis; Output Current:60A; Output Power Max:300W; Output Voltage:5VDC; Series:JWS RoHS Compliant: Yes PDF资料下载
参数资料
| 型号： | FGP20N6S2D |
| 厂商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分类： | IGBT 晶体管 |
| 英文描述： | Switch Mode Power Supply; Output Power:300W; No. of Outputs:1; Output 1 VDC +:5VDC; Output Current 1:60A; Power Supply Mounting:Chassis; Output Current:60A; Output Power Max:300W; Output Voltage:5VDC; Series:JWS RoHS Compliant: Yes |
| 中文描述： | 28 A, 600 V, N-CHANNEL IGBT, TO-220AB |
| 封装： | TO-220AB, 3 PIN |
| 文件页数： | 8/9页 |
| 文件大小： | 232K |
| 代理商： | FGP20N6S2D |
2002 Fairchild Semiconductor Corporation
FGH20N6S2D / FGP20N6S2D / FGB20N6S2D Rev. A1
F
Handling Precautions for IGBTs
Insulated Gate Bipolar Transistors are susceptible to
gate-insulation damage by the electrostatic discharge
of energy through the devices. When handling these
devices, care should be exercised to assure that the
static charge built in the handler
’
s body capacitance
is not discharged through the device. With proper
handling and application procedures, however,
IGBTs are currently being extensively used in
production by numerous equipment manufacturers in
military, industrial and consumer applications, with
virtually no damage problems due to electrostatic
discharge. IGBTs can be handled safely if the
following basic precautions are taken:
1. Prior to assembly into a circuit, all leads should be
kept shorted together either by the use of metal
shorting springs or by the insertion into conduc-
tive material such as
“
ECCOSORBD
LD26
”
or
equivalent.
2. When devices are removed by hand from their
carriers, the hand being used should be grounded
by any suitable means - for example, with a
metallic wristband.
3. Tips of soldering irons should be grounded.
4. Devices should never be inserted into or removed
from circuits with power on.
5.
Gate Voltage Rating
- Never exceed the gate-
voltage rating of V
. Exceeding the rated V
can result in permanent damage to the oxide layer
in the gate region.
6.
Gate Termination
- The gates of these devices
are essentially capacitors. Circuits that leave the
gate open-circuited or floating should be avoided.
These conditions can result in turn-on of the
device due to voltage buildup on the input
capacitor due to leakage currents or pickup.
7.
Gate Protection
- These devices do not have an
internal monolithic Zener diode from gate to
emitter. If gate protection is required an external
Zener is recommended.
Operating Frequency Information
Operating frequency information for a typical device
(Figure 3) is presented as a guide for estimating
device performance for a specific application. Other
typical frequency vs collector current (I
) plots are
possible using the information shown for a typical unit
in Figures 5, 6, 7, 8, 9 and 11. The operating
frequency plot (Figure 3) of a typical device shows
f
MAX1
or f
MAX2
; whichever is smaller at each point.
The information is based on measurements of a
typical device and is bounded by the maximum rated
junction temperature.
f
is defined by f
= 0.05/(t
+ t
).
Deadtime (the denominator) has been arbitrarily held
to 10% of the on-state time for a 50% duty factor.
Other definitions are possible. t
d(OFF)I
and t
d(ON)I
are
defined in Figure 27. Device turn-off delay can
establish an additional frequency limiting condition for
an application other than T
. t
is important
when controlling output ripple under a lightly loaded
condition.
f
MAX2
is defined by f
MAX2
= (P
D
- P
C
)/(E
OFF
+ E
ON2
).
The allowable dissipation (P
D
) is defined by
P
D
= (T
JM
- T
C
)/R
θ
JC
. The sum of device switching
and conduction losses must not exceed P
D
. A 50%
duty factor was used (Figure 3) and the conduction
losses (P
C
) are approximated by P
C
= (V
CE
x I
CE
)/2.
E
and E
are defined in the switching
waveforms shown in Figure 27. E
ON2
is the integral of
the instantaneous power loss (I
CE
CE
) during turn-
on and E
OFF
is the integral of the instantaneous
power loss (I
CE
x V
CE
) during turn-off. All tail losses
are included in the calculation for E
OFF
; i.e., the
collector current equals zero (I
CE
= 0)
ECCOSORBD
is a Trademark of Emerson and Cumming, Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| FGB20N6S2DT | 600V, SMPS II Series N-Channel IGBT with Anti-Parallel StealthTM Diode |
| FGH20N6S2 | Switch Mode Power Supply; Output Power:120W; No. of Outputs:1; Output 1 VDC +:48VDC; Output Current 1:2.5A; Power Supply Mounting:Chassis; Output Current:2.5A; Output Power Max:120W; Output Voltage:48VDC; Series:JWS RoHS Compliant: Yes |
| FGP20N6S2 | 600V, SMPS II Series N-Channel IGBT |
| FGB20N6S2 | 600V, SMPS II Series N-Channel IGBT |
| FGH30N6S2D | 600V, SMPS II Series N-Channel IGBT with Anti-Parallel StealthTM Diode |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FGP-2601-0501-2-0FF | 制造商:YAMAICHI 制造商全称:Yamaichi Electronics Co., Ltd. 功能描述:PC Board Transition Header (2 Rows) |
| FGP-3/4-BLK | 制造商:ICO RALLY 功能描述: 制造商:ICO Rally 功能描述: |
| FGP30B | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Glass Passivated Ultrafast Rectifier |
| FGP30B_11 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Glass Passivated Ultrafast Rectifier |
| FGP30B_12 | 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:Glass Passivated Ultrafast Rectifier |
发布紧急采购，3分钟左右您将得到回复。