- 您现在的位置：买卖IC网 > Datasheet目录326 > FLASHPRO LITE (Microsemi SoC)KIT PROGRAMMER FLASHPRO LITE Datasheet资料下载
参数资料
| 型号： | FLASHPRO LITE |
| 厂商： | Microsemi SoC |
| 文件页数： | 1/2页 |
| 文件大小： | 0K |
| 描述： | KIT PROGRAMMER FLASHPRO LITE |
| 标准包装： | 1 |
| 类型： | 法兰 |
| 适用于相关产品： | ProASICplus |
| 所含物品： | 编程器 |
| 其它名称： | 1100-1139 |
FlashPro Lite Device Programmer
Quickstart Card
This quickstart card applies only to the FlashPro Lite device programmer.
Kit Contents
Quantity
Description
1
FlashPro Lite programmer standalone unit
1
Ribbon cable for FlashPro Lite
1
IEEE 1284 parallel port cable
Software Installation
If you are already using Libero ? System-on-Chip (SoC) software, you have the FlashPro software
installed as part of this software. If you are using the FlashPro Lite device programmer for
standalone programming or on a dedicated machine, download and install the latest release of the
FlashPro software from the Microsemi SoC Products Group website. The installation will guide you
through the setup. Complete the software installation before connecting the FlashPro Lite device
programmer to your PC. The installation will ask you “Will you be using FlashPro Lite or FlashPro
programmer via parallel port?”, answer “Yes”.
Software releases: www.microsemi.com/soc/download/program_debug/flashpro .
Hardware Installation
1.
Connect the programmer to a parallel printer port on your PC. Connect one end of the IEEE 1284
cable to the programmer ’s connector. Plug the other end of the cable into your parallel printer
port and tighten the screws. You should not have any licensing dongles connected between the
parallel port and cable. Your port settings must be EPP or bidirectional. Microsemi also supports
ECP mode with FlashPro v2.1 software and newer.
2.
Verify that you are connected to the correct parallel port on your computer. Microsemi
recommends that you dedicate a port to the programmer. Connecting to a serial port or a third-
party card can damage the programmer. This type of damage is not covered by the warranty.
3.
Connect the FlashPro Lite ribbon cable to the programming header and turn the target board on.
? 2013 Microsemi Corporation. All rights reserved.
相关PDF资料 |
PDF描述 |
|---|---|
| FLS2100XS | IC CTLR FPS HALF BRIDG LCC 9-SIP |
| FMD15.24G | 1500W 24V DC-INPUT 48V RECTIFIER |
| FMP25.48G | 2500W 48V AC-INPUT RECTIFIER |
| FND850-12DRG | FRONT END DC/DC 850W 12V |
| FND850-12RG | FRONT END DC/DC 850W 12V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FLASHPRO-LM-STD | 功能描述:程序设计器 - 基于处理器 FlashPro-LM STD Ver TI M3 M4 Stellaris RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V |
| FLASHPRO-STM-STD | 制造商:Elprotronic Inc 功能描述:Programmers - Processor Based FlashPro-STM STD Ver STM32xx MCU from ST |
| FLASHREADER-USB | 制造商:DRANETZ BMI 功能描述:USB compatible compact flash c 制造商:DRANETZ BMI 功能描述:USB compatible compact flash card reader 制造商:DRANETZ BMI 功能描述:USB compatible compact flash card reader ;RoHS Compliant: NA |
| FLASH-SATA-16GB-AM4020 | 制造商:Kontron 功能描述:16GB FLASH SATA FOR AM4020M-2.0D-2GS-COM - Boxed Product (Development Kits) |
| FLASH-SATA-16GB-CP6003-SA | 制造商:Kontron 功能描述:16GB SATA SLC NAND FLASH -40+70 - Boxed Product (Development Kits) |
发布紧急采购，3分钟左右您将得到回复。