- 您现在的位置：买卖IC网 > PDF目录67503 > FM31L276-G SPECIALTY CONSUMER CIRCUIT, PDSO14 PDF资料下载
参数资料
| 型号： | FM31L276-G |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| 封装： | GREEN, MS-012AB, SOIC-14 |
| 文件页数： | 11/26页 |
| 文件大小： | 716K |
| 代理商： | FM31L276-G |
FM31L278/L276/L274/L272 - 3V I2C Companion
Rev. 2.0
Jan. 2011
Page 19 of 26
three bytes of a write operation to set the internal
address followed by subsequent read operations.
To perform a selective read, the bus master sends out
the slave address with the LSB set to 0. This specifies
a write operation. According to the write protocol,
the bus master then sends the address bytes that are
loaded into the internal address latch. After the
FM31L27x acknowledges the address, the bus master
issues a Start condition. This simultaneously aborts
the write operation and allows the read command to
be issued with the slave address LSB set to a 1. The
operation is now a read from the current address.
Read operations are illustrated below.
RTC/Companion Write Operation
All RTC and Companion writes operate in a similar
manner to memory writes. The distinction is that a
different device ID is used and only one byte address
is needed instead of two. Figure 16 illustrates a single
byte write to this device.
RTC/Companion Read Operation
As with writes, a read operation begins with the
Slave Address. To perform a register read, the bus
master supplies a Slave Address with the LSB set to
1. This indicates that a read operation is requested.
After receiving the complete Slave Address, the
FM31L27x will begin shifting data out from the
current register address on the next clock. Auto-
increment operates for the special function registers
as with the memory address. A current address read
for the registers look exactly like the memory except
that the device ID is different.
The FM31L27x contains two separate address
registers, one for the memory address and the other
for the register address. This allows the contents of
one address register to be modified without affecting
the current address of the other register. For example,
this would allow an interrupted read to the memory
while still providing fast access to an RTC register. A
subsequent memory read will then continue from the
memory address where it previously left off, without
requiring the load of a new memory address.
However, a write sequence always requires an
address to be supplied.
Figure 16. Current Address Memory Read
Figure 17. Sequential Memory Read
S
A
Slave Address 1
Data Byte
1 P
By Master
By FM31L27x
Start
Address
Stop
Acknowledge
No
Acknowledge
Data
Data Byte
A
Acknowledge
S
A
Slave Address
1
Data Byte
1
P
By Master
By FM31L27x
Start
Address
Stop
Acknowledge
No
Acknowledge
Data
相关PDF资料 |
PDF描述 |
|---|---|
| FM32256-G | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| FM3204-G | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| FM3216-G | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| FM3264-G | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
| FM32272-GTR | SPECIALTY CONSUMER CIRCUIT, PDSO14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FM31L276-GTR | 功能描述:监控电路 64K w/RTC Pwr Mon WDT Bat Sw PF RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| FM31L278 | 制造商:RAMTRON 制造商全称:RAMTRON 功能描述:3V Integrated Processor Companion with Memory |
| FM31L278_11 | 制造商:RAMTRON 制造商全称:RAMTRON 功能描述:3V Integrated Processor Companion with Memory |
| FM31L278G | 制造商:Cypress Semiconductor 功能描述: |
| FM31L278-G | 功能描述:监控电路 256K w/RTC Pwr Mon WDT Bat Sw PF RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。