- 您现在的位置：买卖IC网 > PDF目录12148 > FMN.2M.312.XLCT (LEMO)CONN PLUG 12POS STRGHT PIN CRIMP PDF资料下载
参数资料
| 型号： | FMN.2M.312.XLCT |
| 厂商： | LEMO |
| 文件页数： | 36/40页 |
| 文件大小： | 0K |
| 描述： | CONN PLUG 12POS STRGHT PIN CRIMP |
| 产品培训模块： | M Series |
| 特色产品： | M Series Connectors |
| 标准包装： | 50 |
| 系列： | 2M |
| 连接器类型： | 插头，公引脚 |
| 位置数： | 12 |
| 外壳尺寸 - 插件： | 312 |
| 安装类型： | 自由悬挂 |
| 端子： | 压接 |
| 紧固型： | 有螺纹 |
| 方向： | N（正常型） |
| 防护等级： | IP68 - 防尘，防水 |
| 外壳材料，表面处理： | 铝，镀镍 |
| 触点表面涂层： | 金 |
| 特点： | 屏蔽 |
| 包装： | 散装 |
| 额定电流： | 7A |
| 工作温度： | -55°C ~ 200°C |
| 配套产品： | 1124-1206-ND - CONN RCPT 12POS PNL MT SKT W/NUT 1124-1198-ND - CONN RCPT 12POS PNL MT SKT W/NUT |
| 相关产品： | 1124-1175-ND - CAP FOR PLUG (CDF) |
| 其它名称： | 1124-1192 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页
?
?
Assembly instructions for plugs and sockets
FG ●
2
1
PH ●
PB ●
2
1
L ± 0.5
T ± 0.2
1
1.
Cable preparation
First place the heatshrink boot ? over
the cable. Strip the cable according
to dimensions of the table, then widen
Series
0M to 5M
L
20
S
15
T
3.5
S ± 0.5
the shield.
Note : dimensions are in mm.
2.1 With shielded cables, widen and pull the shield all the way to the back.
2
2
Crimp
Crimp
Steel tie-wrap band (~3 mm wide)
2. Cable termination
Fix the appropriate positioner onto the crimping tool and set the selec-
tor to the number corresponding to the AWG of the conductor used as
indicated on the positioner label.
Fit the conductor into the contact ? ; make sure it is visible through the
contact’s inspection hole.
Slide the conductor-contact assembly into the open crimping tool; make
sure that the contact is pushed fully into the positioner. Close the tool.
Remove from crimping tool and check that conductor is secure in
contact and shows in inspection hole.
into the the cable seal.
2.2 Arrange rear conductor-contact assemblies according to the markings,
Push them deeply into the insulator, using tweezers if necessary;
check that all the contacts are correctly located in the insulator: 1)
by verifying the alignment of the contacts at the front of the insulator
and 2) by gently pulling on each conductor.
Verification should also be made using the appropriate retention tes-
ting tool.
Bring it with a band-it the of furnished)
2.3 Secure the shield around tie-wrap (not connector. to fix the shield in place.
Cut off the possible shield surplus.
Steel tie-wrap band (~3 mm wide)
34
Heat
Heat
2.4 Put the heatshrink boot in place and heat gently until it retracts.
www.lemo.com
相关PDF资料 |
PDF描述 |
|---|---|
| VJ1808Y471JBFAT4X | CAP CER 470PF 2KV 5% X7R 1808 |
| VJ1808Y471JBRAT4X | CAP CER 470PF 1.5KV 5% X7R 1808 |
| VJ1808Y681JBFAT4X | CAP CER 680PF 2KV 5% X7R 1808 |
| VJ1808Y681JBRAT4X | CAP CER 680PF 1.5KV 5% X7R 1808 |
| VE-JTJ-IW-S | CONVERTER MOD DC/DC 36V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FMN-3306S | 制造商:Sanken Electric Co Ltd 功能描述:Box |
| FMN-4206S | 制造商:SANKEN 制造商全称:Sanken electric 功能描述:Silicon Diode |
| FMN-4306S | 制造商:Sanken Electric Co Ltd 功能描述:Box |
| FMN-5 | 功能描述:D-Sub后壳 R/A CABLE OUTLET METAL RoHS:否 制造商:Amphenol Commercial Products 类型:Two Piece Backshell 电缆引入数量:1 电缆引入角:Straight 系列:17E 电缆直径: 位置数量:9 外壳大小:E 外壳电镀:Zinc |
| FMN-G12S | 制造商:Sanken Electric Co Ltd 功能描述:Box |
发布紧急采购，3分钟左右您将得到回复。