- 您现在的位置：买卖IC网 > PDF目录6520 > FOD2711AV (Fairchild Optoelectronics Group)OPTOISOLATOR ERROR AMP 8-DIP PDF资料下载
参数资料
| 型号： | FOD2711AV |
| 厂商： | Fairchild Optoelectronics Group |
| 文件页数： | 11/15页 |
| 文件大小： | 0K |
| 描述： | OPTOISOLATOR ERROR AMP 8-DIP |
| 标准包装： | 1,000 |
| 通道数： | 1 |
| 输入类型： | DC |
| 电压 - 隔离： | 5000Vrms |
| 电流传输比（最小值）： | 100% @ 10mA |
| 电流传输比（最大）： | 200% @ 10mA |
| 输出电压： | 70V |
| 电流 - 输出 / 通道： | 50mA |
| Vce饱和（最大）： | 400mV |
| 输出类型： | 晶体管 |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.400"，10.16mm） |
| 包装： | 散装 |
The FOD2711A
R TOP V OUT
-------------------------------- > 80 μ A
----------------------------------- < 926 μ A or R COLLECTOR > 5.4K ? ;
The FOD2711A is an optically isolated error amplifier. It
incorporates three of the most common elements neces-
sary to make an isolated power supply, a reference volt-
age, an error amplifier, and an optocoupler. It is
functionally equivalent to the popular AZ431L shunt volt-
age regulator plus the CNY17F-3 optocoupler.
Powering the Secondary Side
The LED pin in the FOD2711A powers the secondary
side, and in particular provides the current to run the
LED. The actual structure of the FOD2711A dictates the
minimum voltage that can be applied to the LED pin: The
error amplifier output has a minimum of the reference
voltage, and the LED is in series with that. Minimum volt-
age applied to the LED pin is thus 1.24V + 1.5V = 2.74V.
This voltage can be generated either directly from the
output of the converter, or else from a slaved secondary
winding. The secondary winding will not affect regula-
tion, as the input to the FB pin may still be taken from the
output winding.
The LED pin needs to be fed through a current limiting
resistor. The value of the resistor sets the amount of cur-
rent through the LED, and thus must be carefully
selected in conjunction with the selection of the primary
side resistor.
Feedback
Output voltage of a converter is determined by selecting
a resistor divider from the regulated output to the FB pin.
The FOD2711A attempts to regulate its FB pin to the
reference voltage, 1.24V. The ratio of the two resistors
should thus be:
-------------------------- = -------------- – 1
R BOTTOM V REF
The absolute value of the top resistor is set by the input
offset current of 0.8μA. To achieve 1% accuracy, the
resistance of R TOP should be:
V OUT – 1.24
R TOP
?2010 Fairchild Semiconductor Corporation
FOD2711A Rev. 1.0.0
11
Compensation
The compensation pin of the FOD2711A provides the
opportunity for the designer to design the frequency
response of the converter. A compensation network may
be placed between the COMP pin and the FB pin. In
typical low-bandwidth systems, a 0.1μF capacitor may
be used. For converters with more stringent require-
ments, a network should be designed based on mea-
surements of the system’s loop. An excellent reference
for this process may be found in “Practical Design of
Power Supplies” by Ron Lenk, IEEE Press, 1998.
Secondary Ground
The GND pin should be connected to the secondary
ground of the converter.
No Connect Pins
The NC pins have no internal connection. They should
not have any connection to the secondary side, as this
may compromise the isolation structure.
Photo-Transistor
The Photo-transistor is the output of the FOD2711A. In a
normal configuration the collector will be attached to a
pull-up resistor and the emitter grounded. There is no
base connection necessary.
The value of the pull-up resistor, and the current limiting
resistor feeding the LED, must be carefully selected to
account for voltage range accepted by the PWM IC, and
for the variation in current transfer ratio (CTR) of the
opto-isolator itself.
Example: The voltage feeding the LED pins is +12V, the
voltage feeding the collector pull-up is +10V, and the
PWM IC is the Fairchild KA1H0680, which has a 5V ref-
erence. If we select a 10K ? resistor for the LED, the
maximum current the LED can see is:
(12V–2.74V) / 10k ? = 926μA.
The CTR of the opto-isolator is a minimum of 100%, and
so the minimum collector current of the photo-transistor
when the diode is full on is also 926μA. The collector
resistor must thus be such that:
10V – 5V
R COLLECTOR
select 10k ? to allow some margin.
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| YFT-20-05-H-05-SB | CONN HEADER 100POS 1.27MM GOLD |
| JW1AFSN-DC12V | RELAY GEN PURPOSE SPST 10A 12V |
| FOD2711ATV | OPTOISOLATOR ERROR AMP 8-DIP |
| QMSS-026-06.75-H-D-A | CONN HEADER .635MM 52POS DL SMD |
| 3505-8024 | CONN RETAINER CLIP 24POS SHORT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FOD2711S | 功能描述:光隔离放大器 Error amplifier Optocoupler RoHS:否 制造商:Avago Technologies 绝缘电压:5000 Vrms 参考电压: 电流传递比: 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| FOD2711SD | 功能描述:光隔离放大器 Error amplifier Optocoupler RoHS:否 制造商:Avago Technologies 绝缘电压:5000 Vrms 参考电压: 电流传递比: 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| FOD2711SDV | 功能描述:光隔离放大器 Error amplifier Optocoupler RoHS:否 制造商:Avago Technologies 绝缘电压:5000 Vrms 参考电压: 电流传递比: 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| FOD2711SV | 功能描述:光隔离放大器 Error amplifier Optocoupler RoHS:否 制造商:Avago Technologies 绝缘电压:5000 Vrms 参考电压: 电流传递比: 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| FOD2711T | 功能描述:光隔离放大器 Error amplifier Optocoupler RoHS:否 制造商:Avago Technologies 绝缘电压:5000 Vrms 参考电压: 电流传递比: 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。