- 您现在的位置：买卖IC网 > PDF目录20386 > FPSS1U (TDK-Lambda Americas Inc)RACK 3 SLOT FOR FPS1000 PDF资料下载
参数资料
| 型号： | FPSS1U |
| 厂商： | TDK-Lambda Americas Inc |
| 文件页数： | 13/57页 |
| 文件大小： | 0K |
| 描述： | RACK 3 SLOT FOR FPS1000 |
| 视频文件： | Redundant Power Systems |
| 标准包装： | 1 |
| 系列： | FPS |
| 附件类型： | 机架系统 |
| 适用于相关产品： | FPS1000 系列 |
| 配用： | 285-1239-ND - PWR SUP FNT END 48V 1008W 21A 285-1238-ND - PWR SUP FNT END 32V 992W 31A 285-1237-ND - PWR SUP FNT END 24V 960W 40A |
| 其它名称： | 285-1240 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页
3.7.7 Input/Output connector information
The FPS1000 series uses male connector PCIB24W9M400A1, Positronic connector. To mate FPS1000
series to the load circuitry, use female connector PCIB24W9F400A1-S1031, Positronic connector.
Refer to Table 3-4 and to the Outline drawing in chapter 2 for the connector pinout description.
Pin No
1,2,4
3,5,6
7
8
9
10
11
12
13
14
15
16
17
18
19,20,21
22
23
24
Function
+V
-V
On/Off control
+Sense
DC_OK
Signal_Return
AC_Fail
Over
Temperature
Alarm
-Sense
V_Trim
CS
+12V Auxiliary
SDA
SCL
A0, A1, A2
ACG
AC Line
AC Neutral
Description
Positive output voltage. Maximum current capacity: 24A/contact.
Negative output voltage. Maximum current capacity: 24A/contact.
Turns the output to On and Off by electrical signal or dry contact between pin 7
and pin 10 (Signal Return). 0~0.6V or Short: On, 2~15V or Open: Off.
The maximum source current is 2.6mA.
Positive sensing. The +Sense signal should be connected to the positive terminal
of the load. The +Sense and -Sense leads should be twisted pair to minimize noise
pick-up effect. The maximum load wires drop compensation is 1V/wire.
Open collector signal, referenced to pin 10 (Signal Return). On when Vout ≥ 80%+/-
5% of its rated value. The maximum sink current is 10mA and the maximum
external voltage is 15V.
Return for the following control and supervisory signals: On/Off, DC_OK,
Over_temperature Alarm, AC_Fail, Auxiliary 12V supply. The Signal return is isolated
from the output terminals.
Open collector signal, referenced to pin 10 (Signal Return). On when the input
voltage is ≥ 85Vrms. The maximum sink current is 10mA and the maximum external
voltage is15Vdc.
Open collector signal, referenced to pin 10 (Signal Return). On when the internal
temperature is within safe limit, Off approx. 10 ° C below Thermal shut down. The
maximum sink current is 10mA and the maximum external voltage is 15V.
Negative sensing. The -S signal should be connected to the negative terminal of
the load. The -S and +S leads should be twisted pair to minimize noise pick-up
effect. The maximum load wires drop compensation is 1V/wire.
Connection for output voltage trimming. The voltage can be trimmed within its
range specifications.
Current sharing signal. When units are connected in parallel, the CS pins of the
units should be connected to allow current balance between units.
Auxiliary voltage output, 11.2~12.5V, referenced to pin 10 (Signal Return). The
maximum load current is 0.25A. This output has built in Oring diode and is not
controlled by the On/Off control.
Serial Data used in the I 2 C interface option. Refer to the I 2 C interface description.
Serial Clock used in the I 2 C interface option. Refer to the I 2 C interface description.
I 2 C interface address lines. Refer to the I 2 C interface description in Chapter 7.
AC Ground connection, refer to the safety instructions for safety standards requirements.
For "/P" models the AC Ground is connected via the front panel IEC inlet.
AC Line connection, refer to the safety instructions for safety standards requirements.
For "/P" models the AC Line is connected via the front panel IEC inlet.
AC Neutral connection, refer to the safety instructions for safety standards requirements.
For "/P" models the AC Neutral is connected via the front panel IEC inlet.
Table 3-4: Rear In/Out connector pins function description
3.7.8 REPACKAGING FOR SHIPMENT
The original packaging material is reusable. If the original package is not available, contact the Lambda
Sales or service facility near you for details on obtaining suitable packaging and shipping information.
To ensure safe transportation of the instrument, it is recommended to use the original package.
Please attach a tag to the power supply describing the problem and specifying the owner, model number
and serial number of the power supply.
10
相关PDF资料 |
PDF描述 |
|---|---|
| R0.5Z-1212/P-R | CONV DC/DC 0.5W 12V IN 12V OUT |
| 1PS59SB16,115 | DIODE SCHOTTKY 30V 200MA SC59 |
| T95D107K016HSSS | CAP TANT 100UF 16V 10% 2917 |
| T95R336M035CZSS | CAP TANT 33UF 35V 20% 2824 |
| 356-018-526-104 | CARDEDGE 18POS .156 BLACK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FPSS1U/P | 功能描述:线性和开关式电源 1U Rack 85-265VAC Single output RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度: |
| FPSS1U/P-HFP | 制造商:TDK-Lambda Corporation 功能描述:85-265VAC,RA,CK1.72" X 19" X 13.8", HAZMAT - Bulk |
| FPSS1U-HFP | 制造商:TDK-Lambda Corporation 功能描述:85-265VAC,RA,CK1.72" X 19" X 13.8", HAZMAT - Bulk |
| FPS-T | 功能描述:磁性/簧片开关 Flood Prevent Switch Level Sensor Kit RoHS:否 制造商:MEDER electronic (Standex) 开关类型:Reed 触点形式:1 Form A (SPST-NO) 触点额定值:10 VA 操作范围:10 At to 50 At 工作间隙: 磁铁类型: 颜色: 端接类型:Axial 封装:Bulk |
| FPST1U | 功能描述:线性和开关式电源 1U Rack 85-265VAC Triple output RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度: |
发布紧急采购，3分钟左右您将得到回复。