参数资料
| 型号： | FR3-32M |
| 厂商： | TechTools |
| 文件页数： | 24/38页 |
| 文件大小： | 0K |
| 描述： | EMULATOR MEMORY FLEXROM 3 |
| 标准包装： | 1 |
| 系列： | FlexROM™ III |
| 类型： | 存储器 |
| 适用于相关产品： | 外部 FLASH、EPROM 或 SRAM 设备 |
| 所含物品： | 需要 FR3 FlexROM III 仿真器、缆线（菊花链、LPT、迷你型夹和目标）、软件、有源缆线模块 |
| 其它名称： | Q1470431 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
Fast CS Access
Normally, FlexROM III drives its SRAM CS (chip select) lines with a buffered version of your target’s CS
line and provides stable data 45ns after the last transition on address or after CS goes active – whichever is
later.
Enabling FAST CS ACCESS causes FlexROM III to force its SRAM CS lines always active. FlexROM
III’s output buffers are still gated with your target CS so the emulator continues to honor all target control
signals. This reduces the emulator’s Tcs access time from 45ns to 12ns.
Many targets will decode their CS signal off of address lines. This makes the Tcs the determining factor in
setting its ACCESS time requirements. The Tacc might be 45ns but due to decoding delays, the Tcs could
be 30 – 40ns. In this situation, the FAST CS option would allow our 45ns emulator to function properly in
a target that normally requires a 30-40ns emulator.
You normally would not turn this option on unless your target has a Tcs requirement of < 45ns and its
addresses are stable before CS is activated.
Turning on this option will result in higher operating current requirements and could increase system noise
in targets that have extended periods of address line float.
Fast OE Access
Normally, FlexROM III drives its SRAM OE (output enable) lines with a buffered version of your target’s
OE line and provides stable data 45ns after the last transition on address or after CS goes active, or 30ns
after OE goes active – whichever is later.
Enabling FAST OE ACCESS causes FlexROM III to force its SRAM OE lines always active. FlexROM
III’s output buffers are still gated with your target OE so the emulator continues to honor all target control
signals. This reduces the emulator’s OE access time from 30ns to 12ns.
Turning on this option will result in slightly higher operating current requirements and could increase
system noise in some targets during target writes to the emulator.
You normally would not turn on this option unless your target has a Toe timing specification of < 30ns.
However, it generally does not hurt to do so.
It is acceptable to use FAST CS and FAST OE at the same time.
FlexROM III User’s Manual
22
Copyright ? 2001, TechTools
相关PDF资料 |
PDF描述 |
|---|---|
| FS-9062 | JTAG_BOOSTER FOR ANALOG DEVICES |
| FS-977 | JTAG-BOOSTER FOR 386EX 3.3V |
| FS1-R26-2000 | CONN RECEPT MINI SAS 26POS SMD |
| FS1-R26-2001 | CONN RECPT SAS MINI 26POS SMT |
| FS1-S01-146E1 | CONN SNGL M-SAS CAGE KEY 4,6 P1 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FR34 | 制造商:FCI 制造商全称:First Components International 功能描述:3.0 Amp FAST RECOVERY PLASTIC RECTIFIERS |
| FR3492-D | 制造商:BACO Controls Inc 功能描述: |
| FR3492-D1 | 制造商:BACO Controls Inc 功能描述: |
| FR3492-D2 | 制造商:BACO Controls Inc 功能描述: |
| FR3492-D3 | 制造商:BACO Controls Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。