- 您现在的位置：买卖IC网 > Datasheet目录326 > FS-931 (Digi International)JTAG-BOOSTER FOR ELANSC520 3.3V Datasheet资料下载
参数资料
| 型号： | FS-931 |
| 厂商： | Digi International |
| 文件页数： | 9/50页 |
| 文件大小： | 0K |
| 描述： | JTAG-BOOSTER FOR ELANSC520 3.3V |
| 标准包装： | 1 |
| 系列： | Digi/FS Forth |
| 类型： | 闪存 |
| 适用于相关产品： | AMD ElanSC520 |
| 所含物品： | 编程器和关联的接口软件 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
JTAG-Booster for AMD élanSC520
1.4.Trouble Shooting
Avoid long distances between your Host-PC and the target. If you are using
standard parallel extension cable, the JTAG-BOOSTER may not work. Don't use
Dongles between the parallel port and the JTAG-BOOSTER.
Switch off all special modes of your printer port (EPP, ECP, ...) in the BIOS
setup. Only standard parallel port (SPP) mode is allowed.
On very fast PCs there could be verify errors. To avoid this, watch for the
′IO recovery time′-switch in the BIOS Setup which must be turned on. Otherwise
try to slow down your PC by setting the turbo switch off.
When using older flash devices (nearly maximum erase cycles reached), we
propose to use the /VERIFY option. This is also true for the relatively slow 3 Volt
only flash devices.
Some newer fast flash devices need a setup time between address/data and the
write strobe signal. If programming of this devices fails, try with the option
/WRSETUP again.
If there are problems with autodetection of the flash devices use the /DEVICE=
option. To speed up autodetection specify the option /16BIT or /8BIT.
Don't use hardware protected flash memories.
The used chip selects must be defined as output and inactive in the initialization
file (see chapter 1.6 “Initialization file JTAGEL5.INI”). Also the address bits must
be defined as output.
JTAGEL5d.doc
9
相关PDF资料 |
PDF描述 |
|---|---|
| FS-935 | JTAG-BOOSTER FOR IDT64145 3.3V |
| FS-940 | JTAG-BOOSTER FOR ADSP-21XXX 5V |
| FSICEBASE | BASE STATION FSICE FOR MCU MOD |
| FT24C02A-5LR-T | IC EEPROM 2KBIT 1MHZ SOT23-5 |
| FT24C16A-UMR-B | IC EEPROM 16KBIT 1MHZ 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FS-932 | 功能描述:开发板和工具包 - ARM Forth JTAG Booster PC Siemens PCUD 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| FS-935 | 功能描述:开发板和工具包 - ARM Forth JTAG Booster PC IDT64145 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| FS-940 | 功能描述:开发板和工具包 - ARM JTAG Booster PC ADSP-21xxx 5V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| FS-945 | 功能描述:开发板和工具包 - ARM JTAG Booster PC Elan SC400 3.3V RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| FS94NS | 制造商:BOTHHAND 制造商全称:Bothhand USA, LP. 功能描述:SMD, 14 PIN, 10 BASE-T FILTER FOR PCMCIA APPLICATIONS |
发布紧急采购，3分钟左右您将得到回复。