- 您现在的位置：买卖IC网 > PDF目录67582 > FS2660-9EPD7TB1 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | FS2660-9EPD7TB1 |
| 元件分类： | 电源模块 |
| 英文描述： | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | METAL, CASE S02, MODULE |
| 文件页数： | 4/31页 |
| 文件大小： | 633K |
| 代理商： | FS2660-9EPD7TB1 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Cassette Style
100 Watt DC-DC Converters
S Series
Edition 1/01.2000
12/31
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table:
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71
°C (e.g. 85°C) if T
C max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85
°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05089
TA min
TC max
Convection cooling
Fig. 7
Output current derating versus temperature for -7 and -9
units.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Output Protection
Each output is protected against overvoltage which could
occur due to a failure of the control circuit by means of a
voltage suppressor diode which, under worst case condi-
tions, may become a short circuit. The suppressor diodes
are not designed to withstand externally applied over-
voltages. Overload at any of the two outputs will cause a
shut-down of both outputs. A red LED indicates the over-
load condition.
Output Voltage Regulation of Single or Double Output
Modules with Outputs 1 and 2 Connected in Series
Uo
Uo nom
0.98
0.5
0
0.5
1.0
Io1
IoL
Io
Io nom
05068
Fig.8
Uo1 vs. Io1 (typ.) of single output units
Parallel or Series Connection of Units
Single or double output units with equal nominal output volt-
age can be connected in parallel without any precautions
using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note: Parallel connection of double output units should al-
ways include both, main and second output to maintain
good regulation of both outputs.
Not more than 5 units should be connected in parallel.
Series connection of second outputs without involving their
main outputs should be avoided as regulation may be poor.
The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
相关PDF资料 |
PDF描述 |
|---|---|
| FS2660-9EPD9TB1 | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS2660-9ERD5T | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS2660-9RTB1 | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS1001-7EPD2B2 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| FS1001-7ERD2TB1 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FS-267 | 功能描述:ADAPTER JTAG ELAN486/386DRAM RoHS:是 类别:编程器，开发系统 >> 配件 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 标准包装:1 系列:- 附件类型:USB 至 1-Wire? RJ11 适配器 适用于相关产品:1-Wire? 设备 产品目录页面:1429 (CN2011-ZH PDF) |
| FS2775-9RB1 | 制造商:MELCHER 功能描述: 制造商:Power-One 功能描述: |
| FS28-040 | 功能描述:电源变压器 1.1VA 28VCT @ 0.045A Dual Pri. 8 Pin RoHS:否 制造商:Triad Magnetics 功率额定值:12 VA 初级电压额定值:115 V / 230 V 次级电压额定值:12 V / 24 V 安装风格:SMD/SMT 一次绕组:Dual Primary Winding 二次绕组:Dual Secondary Winding 长度:2.5 in 宽度:2 in 高度:1.062 in |
| FS28-040-C2 | 制造商:Triad Magnetics 功能描述:Transformer, class 2/3, 8-pin, 1.1VA, 115/230V x 28VCT at 0.04A, 14V at 0.08A |
| FS28-040-C2-B | 制造商:Triad Magnetics 功能描述:XFRMR LAMINATED 1.1VA THRU HOLE |
发布紧急采购，3分钟左右您将得到回复。